mycnc:cutcharts
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revision | Next revisionBoth sides next revision | ||
mycnc:cutcharts [2017/12/21 13:26] – es | mycnc:cutcharts [2017/12/21 13:42] – es | ||
---|---|---|---|
Line 19: | Line 19: | ||
| MaterialThickness | Material Thickness | | | MaterialThickness | Material Thickness | | ||
| Type | Material Type (Mild Steel, Stainless Stel, Aluminium, Brass) | | | Type | Material Type (Mild Steel, Stainless Stel, Aluminium, Brass) | | ||
- | | CollisionDelayTime | | + | | CollisionDelayTime |
- | | HoldPierceHeightTime; | + | | HoldPierceHeightTime |
+ | | NoMoveAtHolecut | --- | | ||
| Gas_Select1_Type | HPR Automatic gas console Gas Mix Select #1 | | | Gas_Select1_Type | HPR Automatic gas console Gas Mix Select #1 | | ||
| Gas_Select2_Type | HPR Automatic gas console Gas Mix Select #2 | | | Gas_Select2_Type | HPR Automatic gas console Gas Mix Select #2 | | ||
+ | ^ Consumable part numbers ^^ | ||
| ShieldRetainingCap | Shield Retaining Cap part number | | | ShieldRetainingCap | Shield Retaining Cap part number | | ||
| Shield | Shield part number | | | Shield | Shield part number | | ||
Line 30: | Line 32: | ||
| Electrode | Electrode part number | | | Electrode | Electrode part number | | ||
| WaterTube | Water Tube part number | | | WaterTube | Water Tube part number | | ||
- | | NoMoveAtHolecut | --- | | + | ^ Oxy-fuel cutting parameters ^^ |
| TimeIgnitionValve | Oxyfuel cutting: Ignition time | | | TimeIgnitionValve | Oxyfuel cutting: Ignition time | | ||
| TimeIgnitionSparkle | Oxyfuel cutting: Sparkle time | | | TimeIgnitionSparkle | Oxyfuel cutting: Sparkle time | | ||
Line 41: | Line 43: | ||
| AGC_Pierce_OxyHeat | Oxyfuel cutting: Automatic Gas Console - Cutting Oxygen on Ignition | | | AGC_Pierce_OxyHeat | Oxyfuel cutting: Automatic Gas Console - Cutting Oxygen on Ignition | | ||
| AGC_Pierce_OxyCut | Oxyfuel cutting: Automatic Gas Console - Fuel on Ignition | | | AGC_Pierce_OxyCut | Oxyfuel cutting: Automatic Gas Console - Fuel on Ignition | | ||
- | QString | + | | AGC_Cutting_Fuel |
- | | + | | AGC_Cutting_OxyHeat |
- | | + | | AGC_Cutting_OxyCut |
- | | + | | AGC_Pilot_Fuel |
- | | + | | AGC_Pilot_OxyHeat |
- | + | ^ Cutting Parameters ^^ | |
- | + | | CutSpeed | |
- | int id; | + | | Kerf | Kerf Compensation | |
- | QString | + | | CreepTime |
- | + | | CreepSpeed | |
- | //QString CNC_Speed_mid; | + | ^ Torch Height Control Parameters ^^ |
- | //QString CNC_Speed_small; | + | | HC_IgnitionHeight;// |
- | + | | HC_PierceHeight | |
- | QString | + | | HC_CutHeight |
- | | + | | HC_PierceHeightFactor |
- | | + | |
- | + | ||
- | + | ||
- | QString | + | |
- | | + | |
- | | + | |
- | | + | |
QString HC_PierceDelay; | QString HC_PierceDelay; | ||
QString HC_ArcVoltage; | QString HC_ArcVoltage; |
mycnc/cutcharts.txt · Last modified: 2021/10/06 15:19 by ivan