Differences

This shows you the differences between two versions of the page.

--- mycnc:cutcharts [2017/12/21 13:42] – es
+++ mycnc:cutcharts [2017/12/21 14:40] – es
@@ Line 17: / Line 17: @@
 ^ Parameter Name ^ Description ^
+| Technology | Cutting technology (Plasma, Oxy-fuel, laser etc) |
+| Vendor | Cutchart vendor |
+| Revision | Cutchart Revision |
+| TorchType | Torch Type |
 | MaterialThickness | Material Thickness |
-| Type | Material Type (Mild Steel, Stainless Stel, Aluminium, Brass) |
+| MaterialType | Material Type (Mild Steel, Stainless Stel, Aluminium, Brass)  |
+| Process | Process definition (like HPR xd,  Fine-Cut etc) |
+| SpecificMaterial | Specific materail (like Bevel cutting) |
 | CollisionDelayTime | --- |
 | HoldPierceHeightTime | --- |
@@ Line 54: / Line 60: @@
 | CreepSpeed | Creep Speed (see above) |
 ^ Torch Height Control Parameters ^^
-| HC_IgnitionHeight;//TransferHeight;
+| HC_IgnitionHeight | Ignition Height (Transfer Height) |
 | HC_PierceHeight | Pierce Height |
 | HC_CutHeight | Cut Height |
 | HC_PierceHeightFactor | Hypertherm Parameter, different way to program  similar to Pierce Height |
-    QString HC_PierceDelay; //PierceTime;
+| HC_PierceDelay | Pierce Delay (Pierce Time) |
-    QString HC_ArcVoltage;
+| HC_ArcVoltage | Height control reference voltage (defines cutting height) |
-    QString HC_ControlDelay;    //THC Delay
+| HC_ControlDelay | Height control delay - Height control activated after pierce + this delay finished |
+^ Plasma Cutting ^^
+| ProcessCurrent | Plasma: Process current |
+| SetArcCurrent | Set Arc Current parameter to be sent to PLasma SOurce (id supported) |
+| CornerReduction | Reduction Process current on corners to reduce overheat and improve corner cut quality |
+| PlasmaShieldGases | Plasma cutting gases for Plasma and Shield channels |
+| Plasma_Gas | Gas type for Plasma channel |
+| Shield_Gas | Gas type for Shield channel |
+| MixGas1 | HPR Gas console MixGas1 Parameter |
+| MixGas2 | HPR Gas console MixGas2 Parameter |
+^ Plasma Automatic Gas Console ^^
+| AGC_PlasmaPreflow | Plasma: Automatic Gas Console Plasma channel Preflow gas pressure |
+| AGC_ShieldPreflow | Plasma: Automatic Gas Console Shield channel Preflow gas pressure |
+| AGC_PlasmaCutflow | Plasma: Automatic Gas Console Plasma channel Cutflow gas pressure |
+| AGC_ShieldCutflow | Plasma: Automatic Gas Console Shield channel Cutflow gas pressure |
+^ Plasma Manual Gas Console ^^
+| MGC_PlasmaPreflow | Plasma: Manual Gas Console Plasma channel Preflow gas pressure |
+| MGC_ShieldPreflow | Plasma: Manual Gas Console Shield channel Preflow gas pressure |
+| MGC_PlasmaCutflow | Plasma: Manual Gas Console Plasma channel Cutflow gas pressure |
+| MGC_ShieldCutflow | Plasma: Manual Gas Console Shield channel Cutflow gas pressure |
+^ Additional Parameters ^^
+| PS_MarkingDataset | --- |
+| PS_TimeSpeedCountourEnd | --- |
+| PS_OverrideTimeway | --- |
+| PS_WayPlasmaOff | --- |
+| PS_WaySpeedCountourEnd | --- |
+| PS_PierceReductionDistance | --- |
+| PS_PierceReduction | --- |
+| PS_CornerCurrentReduction | --- |
-    QString Technology;
-    QString Process;    //like HPR xd,  fine-cut etc
-    QString Vendor;
-    QString Revision;
-    QString TorchType;
-    QString MaterialType;
-    QString SpecificMaterial;
-    QString ProcessCurrent;
-    QString SetArcCurrent;  //
-    QString CornerReduction;
-    QString PlasmaShieldGases;
-    //QString Plasma_Gas;
-    //QString Shield_Gas;
-    QString MixGas1;
-    QString MixGas2;
-    QString AGC_PlasmaPreflow;
-    QString AGC_ShieldPreflow;
-    QString AGC_PlasmaCutflow;
-    QString AGC_ShieldCutflow;
-    QString MGC_PlasmaPreflow;
-    QString MGC_ShieldPreflow;
-    QString MGC_PlasmaCutflow;
-    QString MGC_ShieldCutflow;
-    QString PS_MarkingDataset;
-    QString PS_TimeSpeedCountourEnd;
-    QString PS_OverrideTimeway;
-    QString PS_WayPlasmaOff;
-    QString PS_WaySpeedCountourEnd;
-    QString PS_PierceReductionDistance;
-    QString PS_PierceReduction;
-    QString PS_CornerCurrentReduction;