mycnc:flatbed_correction
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
mycnc:flatbed_correction [2019/06/17 12:44] – ivan | mycnc:flatbed_correction [2021/05/21 11:44] – ivan | ||
---|---|---|---|
Line 1: | Line 1: | ||
=====myCNC Flatbed Correction===== | =====myCNC Flatbed Correction===== | ||
- | This article discusses the flatbed correction feature built into myCNC software which is often useful when the working table is not even or has certain spots which are higher or lower than the reference position. This is especially useful in cases when something like a tangential knife needs to go over the uneven table, with up to a millimeter of play being involved, resulting in a cut that does not actually go through the working material properly. | + | This article discusses the flatbed correction feature built into myCNC software which is often useful when the working table is not even or has certain spots which are higher or lower than the reference position. This is especially useful in cases when something like a tangential knife needs to go over the uneven table, resulting in a cut that does not actually go through the working material properly, or alternatively a cut that goes far too deep into the material. |
- | In order to account for this, go into **Settings > Config > Technology > Special Purpose > Flatbed Correction**. | + | In order to account for this, flatbed correction is used. |
- | The screen presented to you will look similar to the following | + | The following |
- | {{: | + | {{youtube> |
- | First of all, **enable** the flatbed correction: | + | To set up flatbed correction, go into **Settings > Config > Technology > Special Purpose > Flatbed Correction**. The screen presented to you will be the following: |
- | {{: | + | {{: |
- | Next, the table on the settings page presents a number | + | After the setup process has been completed, a table of points |
- | {{:mycnc:flatbed-003-m402.png}} | + | * **Note:** Flatbed correction **must be disabled** prior to beginning taking the measurements, |
- | In order to remove any of the table level discrepancy values, you can press the Delete button for each particular value. | + | * The **Auto Measure Procedure** button can be pressed |
- | {{:mycnc:flatbed-002-checkmarks.png}} | + | * **Note:** If you leave the flatbed |
- | By adding these correction points, myCNC software will use triangulation in order to create | + | After the measurement procedure has completed and all the points are logged, select the Reference Z value. The Reference Z value should be chosen to be between the minimum and the maximum measure point, preferably somewhere in the middle between the two. |
+ | |||
+ | * **Note:** The myCNC flatbed correction feature is limited to 1000 pulses (+ or -) from the Reference Z position. Depending on the number of pulses per unit that you have set up in the Axes/Motors window, this may be anywhere from a centimeter to a fraction of a millimeter. If the machine moves above or below the 1000 pulses limit, it will not be able to accurately correct for flatbed distortion until it is back down below the limit. This is why the reference Z value must be selected correctly. | ||
+ | |||
+ | * In order to use the M402 macro for manual point measurement, | ||
+ | |||
+ | After the measurements have been taken and the Reference Z has been entered, press the Save CFG button, enable Flatbed correction and reload the application. | ||
+ | |||
+ | By adding these correction points, myCNC software will create | ||
+ | |||
+ | ====M402 macro==== | ||
+ | |||
+ | The code for the M402 macro can be found below: | ||
+ | |||
+ | < | ||
+ | (Surface measure macro) | ||
+ | G28.2 Z0 (save current Z into Register1.Z) | ||
+ | |||
+ | M88 L1 P15 (watch for input(P) to be closed (L1) - EDIT THIS) | ||
+ | G91 G0 Z -35.000 F 200 | ||
+ | (move down, stop if sensor triggered) | ||
+ | G91 G0 Z 2.000 F 400 | ||
+ | M89 L1 P15 (watch for input(P) to be closed (L1) - EDIT THIS) | ||
+ | G91 G0 Z -2.000 F 20.0 | ||
+ | |||
+ | G4 P0.2 | ||
+ | |||
+ | G90 G10 L81 P8171 Q5021 | ||
+ | G90 G10 L81 P8172 Q5022 | ||
+ | G90 G10 L81 P8173 Q5023 | ||
+ | |||
+ | G90 G10 L80 P8170 Q1 | ||
+ | |||
+ | G91 G0 Z10 | ||
+ | </ | ||
+ | |||
+ | Here, you have to edit the two lines with the EDIT THIS comments. In the input P, you have to specify the input number for the sensor (set as 15 in this example), and in the L field you have to specify the behaviour that will be interpreted as the sensor being triggered (0 for a normally closed sensor which will be opened when triggered, and 1 for a normally open sensor which will be closed at contact). |
mycnc/flatbed_correction.txt · Last modified: 2022/12/01 11:37 by ivan