mycnc:gcodes_list
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
mycnc:gcodes_list [2019/09/26 14:39] – ivan | mycnc:gcodes_list [2021/04/21 13:38] – ivan | ||
---|---|---|---|
Line 23: | Line 23: | ||
| G18 | Plane ZX | | | G18 | Plane ZX | | ||
| G19 | Plane YZ | | | G19 | Plane YZ | | ||
- | | G20 | Unit Inches | | | + | | G20 | Set Units to Inches | | |
- | | G21 | Unit Metric | | | + | | G21 | Set Units to Metric | | |
| G28 | [[mycnc: | | G28 | [[mycnc: | ||
| G28.1 | Home Position Set | | | G28.1 | Home Position Set | | ||
Line 32: | Line 32: | ||
| G28.5 | Home Position #1 Restore | | | G28.5 | Home Position #1 Restore | | ||
| G28.6 | Home Position #2 Restore | | | G28.6 | Home Position #2 Restore | | ||
- | | G28.7 | Home Position #3 Restore | | ||
| G28.7 | Home Position #3 Restore | | | G28.7 | Home Position #3 Restore | | ||
| G28.9 | Home Position Address | | | G28.9 | Home Position Address | | ||
Line 39: | Line 38: | ||
| G33 | Spindle Synchronization | | | G33 | Spindle Synchronization | | ||
| G33 | Spindle Synchronization | | | G33 | Spindle Synchronization | | ||
- | | G38.2 | G38.2 Probing | | + | | G38.2 | G38.2 Probing |
| G38.3 | G38.3 Probing | | | G38.3 | G38.3 Probing | | ||
| G38.4 | G38.4 Probing | | | G38.4 | G38.4 Probing | | ||
| G38.5 | G38.5 Probing | | | G38.5 | G38.5 Probing | | ||
| G38.9 | Tool Measure | | | G38.9 | Tool Measure | | ||
- | | G40 | Tool Correction Cancel | | + | | G40 | Tool Correction Cancel |
- | | G41 | Tool Correction Left | | + | | G41 | Tool Correction Left | | {{: |
- | | G42 | Tool Correction Right | | + | | G42 | Tool Correction Right | | {{: |
| G43 | G43 Tool Length Offset | | | G43 | G43 Tool Length Offset | | ||
| G44 | G44 Tool Length Offset | | | G44 | G44 Tool Length Offset | | ||
Line 69: | Line 68: | ||
| G64 | < | | G64 | < | ||
| G65 | G-code macro | M | | | G65 | G-code macro | M | | ||
- | | G73 | Cycle Deep Hole Drilling | M | | + | | G73 | [[mycnc: |
| G74 | Cycle Left Hand Tapping | M | | | G74 | Cycle Left Hand Tapping | M | | ||
| G76 | Cycle Lathe Thread | L | | | G76 | Cycle Lathe Thread | L | | ||
| G76 | Motion Mode Cancel| L | | | G76 | Motion Mode Cancel| L | | ||
| G80 | Cancel Motion Mode | | | | G80 | Cancel Motion Mode | | | ||
- | | G81 | Cycle Drilling | | | + | | G81 | [[mycnc: |
| G82 | Cycle Drilling Dwell | | | | G82 | Cycle Drilling Dwell | | | ||
- | | G83 | Cycle Peck Drilling | | | + | | G83 | [[mycnc: |
| G84 | Cycle Right Hand Tapping | | | | G84 | Cycle Right Hand Tapping | | | ||
| G85 | Cycle Boring No Dwell Feed Out | | | G85 | Cycle Boring No Dwell Feed Out | | ||
Line 94: | Line 93: | ||
| G97 | Set Spindle Speed | L | (revolutions per minute) | | | G97 | Set Spindle Speed | L | (revolutions per minute) | | ||
| G98 | Turn Feedrate per Minute | L | | | G98 | Turn Feedrate per Minute | L | | ||
- | | G98 | Canned Return Back to initial height | M | | | + | | G98 | Canned Return Back to initial height | M | On mill machines, G98 allows to return the tool back to initial height Z during the canned return process. {{: |
| G99 | Turn Feedrate per Revolution | L | | | G99 | Turn Feedrate per Revolution | L | | ||
- | | G99 | Canned Return to a set height | M | {{: | + | | G99 | Canned Return to a set height | M | As opposed to G98, which returns the tool to the initial height (height before cutting), G99 returns the tool to some set height Z. {{: |
| G150 | Tool Correction Radius Set | | | G150 | Tool Correction Radius Set | | ||
^ Miscellaneous M-codes ^^^^ | ^ Miscellaneous M-codes ^^^^ | ||
Line 133: | Line 132: | ||
| M64 | Turn On binary output pin | PLC | | | | M64 | Turn On binary output pin | PLC | | | ||
| M65 | Turn Off binary output pin | PLC | | | | M65 | Turn Off binary output pin | PLC | | | ||
- | | M71 | Start Cutting | PLC | Cutting Tables | | + | | M71 | Start Cutting |
| M72 | Begin Plasma Marking Section | PLC | Cutting Tables | | | M72 | Begin Plasma Marking Section | PLC | Cutting Tables | | ||
| M73 | End Plasma Marking Section | PLC | Cutting Tables | | | M73 | End Plasma Marking Section | PLC | Cutting Tables | |
mycnc/gcodes_list.txt · Last modified: 2023/09/29 14:15 by ivan