mycnc:gcodes_list
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
mycnc:gcodes_list [2019/09/26 14:48] – ivan | mycnc:gcodes_list [2019/09/27 09:21] – ivan | ||
---|---|---|---|
Line 23: | Line 23: | ||
| G18 | Plane ZX | | | G18 | Plane ZX | | ||
| G19 | Plane YZ | | | G19 | Plane YZ | | ||
- | | G20 | Unit Inches | | | + | | G20 | Set Units to Inches | | |
- | | G21 | Unit Metric | | | + | | G21 | Set Units to Metric | | |
| G28 | [[mycnc: | | G28 | [[mycnc: | ||
| G28.1 | Home Position Set | | | G28.1 | Home Position Set | | ||
Line 39: | Line 39: | ||
| G33 | Spindle Synchronization | | | G33 | Spindle Synchronization | | ||
| G33 | Spindle Synchronization | | | G33 | Spindle Synchronization | | ||
- | | G38.2 | G38.2 Probing | | + | | G38.2 | G38.2 Probing |
| G38.3 | G38.3 Probing | | | G38.3 | G38.3 Probing | | ||
| G38.4 | G38.4 Probing | | | G38.4 | G38.4 Probing | | ||
| G38.5 | G38.5 Probing | | | G38.5 | G38.5 Probing | | ||
| G38.9 | Tool Measure | | | G38.9 | Tool Measure | | ||
- | | G40 | Tool Correction Cancel | | + | | G40 | Tool Correction Cancel |
- | | G41 | Tool Correction Left | | + | | G41 | Tool Correction Left | | {{: |
- | | G42 | Tool Correction Right | | + | | G42 | Tool Correction Right | | {{: |
| G43 | G43 Tool Length Offset | | | G43 | G43 Tool Length Offset | | ||
| G44 | G44 Tool Length Offset | | | G44 | G44 Tool Length Offset | | ||
Line 94: | Line 94: | ||
| G97 | Set Spindle Speed | L | (revolutions per minute) | | | G97 | Set Spindle Speed | L | (revolutions per minute) | | ||
| G98 | Turn Feedrate per Minute | L | | | G98 | Turn Feedrate per Minute | L | | ||
- | | G98 | Canned Return Back to initial height | M | {{: | + | | G98 | Canned Return Back to initial height | M | On mill machines, G98 allows to return the tool back to initial height Z during the canned return process. |
| G99 | Turn Feedrate per Revolution | L | | | G99 | Turn Feedrate per Revolution | L | | ||
- | | G99 | Canned Return to a set height | M | {{: | + | | G99 | Canned Return to a set height | M | As opposed to G98, which returns the tool to the initial height (height before cutting), G99 returns the tool to some set height Z. {{: |
| G150 | Tool Correction Radius Set | | | G150 | Tool Correction Radius Set | | ||
^ Miscellaneous M-codes ^^^^ | ^ Miscellaneous M-codes ^^^^ |
mycnc/gcodes_list.txt · Last modified: 2023/09/29 14:15 by ivan