mycnc:gcodes_list
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
mycnc:gcodes_list [2018/09/25 09:53] – skirillov | mycnc:gcodes_list [2019/09/26 09:41] – ivan | ||
---|---|---|---|
Line 1: | Line 1: | ||
===== G-Codes list ===== | ===== G-Codes list ===== | ||
+ | |||
+ | Below is a list of G-codes currently implemented in the myCNC system. | ||
^ G-codes ^^^^ | ^ G-codes ^^^^ | ||
Line 23: | Line 25: | ||
| G20 | Unit Inches | | | | G20 | Unit Inches | | | ||
| G21 | Unit Metric | | | | G21 | Unit Metric | | | ||
- | | G28 | G28 Home | | + | | G28 | [[mycnc: |
| G28.1 | Home Position Set | | | G28.1 | Home Position Set | | ||
| G28.2 | Home Position #1 Save | | | G28.2 | Home Position #1 Save | | ||
Line 67: | Line 69: | ||
| G64 | < | | G64 | < | ||
| G65 | G-code macro | M | | | G65 | G-code macro | M | | ||
- | | G68 | Rotation Coordinates Mode On | M | | ||
- | | G69 | Rotation Coordinates Mode Off | M | | ||
| G73 | Cycle Deep Hole Drilling | M | | | G73 | Cycle Deep Hole Drilling | M | | ||
| G74 | Cycle Left Hand Tapping | M | | | G74 | Cycle Left Hand Tapping | M | | ||
Line 120: | Line 120: | ||
| M20 | Start Cutting | PLC | Cutting Tables | | | M20 | Start Cutting | PLC | Cutting Tables | | ||
| M21 | Stop Cutting | PLC | Cutting Tables | | | M21 | Stop Cutting | PLC | Cutting Tables | | ||
- | | M23 | Thread Finishing | + | | M23 | [[mycnc: |
- | | M24 | Thread Finishing | + | | M24 | [[mycnc: |
- | | M30 | End Program with Rewind Pointer | Macro | | | + | | M30 | [[mycnc: |
| M41 | Set Low Gears | PLC | | | | M41 | Set Low Gears | PLC | | | ||
| M41 | Set High Gears | PLC | | | | M41 | Set High Gears | PLC | | | ||
Line 258: | Line 258: | ||
==== M08 - Plasma cutting table - Drill Marking ==== | ==== M08 - Plasma cutting table - Drill Marking ==== | ||
- | M08 is used for Drill Marking operations on Plasma Cutting machines which have drill head. Drill Marking procedure is - | + | M08 is used for Drill Marking operations on Plasma Cutting machines which have drill head. Drill Marking procedure is the following: |
- | * Drill Head Cylinder and Drill Powr turned ON | + | * Drill Head Cylinder and Drill Power turned ON |
- | * Drill Head moves down on **Probing Speed** | + | * Drill Head moves down on **Probing Speed** |
* Moving speed switched to **Drill Speed** and the Head move lower to programmed **Drill Depth** | * Moving speed switched to **Drill Speed** and the Head move lower to programmed **Drill Depth** | ||
* Drill Head moves up to **Lift Height** | * Drill Head moves up to **Lift Height** |
mycnc/gcodes_list.txt · Last modified: 2023/09/29 14:15 by ivan