User Tools

Site Tools


mycnc:global_variables

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revisionBoth sides next revision
mycnc:global_variables [2019/08/30 11:45] ivanmycnc:global_variables [2019/08/30 11:47] ivan
Line 12: Line 12:
 |GVAR_MODAL_G54_G59 | 4014 | Modal state of G54-G59 | |GVAR_MODAL_G54_G59 | 4014 | Modal state of G54-G59 |
 |GVAR_MODAL_G17_G19 | 4016 | Modal state of G17-G19 | |GVAR_MODAL_G17_G19 | 4016 | Modal state of G17-G19 |
-|GVAR_TOOL_1_X_CORRECTION | 4600 | (+98) Tool correction (small value corrections in the x direction) +|GVAR_TOOL_1_X_CORRECTION | 4600 | (+98) Tool correction (small value corrections in the x direction) | 
-|GVAR_TOOL_1_Z_CORRECTION | 4700 | (+98) Tool correction (small value corrections) in the z direction)+|GVAR_TOOL_1_Z_CORRECTION | 4700 | (+98) Tool correction (small value corrections) in the z direction) |
 |<del>GVAR_RUNNING_STOP</del> | 4800 | | |<del>GVAR_RUNNING_STOP</del> | 4800 | |
 |<del>GVAR_CURRENT_BLOCK_END_POSITION</del> | 5001 | (+8) program position at the end of current block | |<del>GVAR_CURRENT_BLOCK_END_POSITION</del> | 5001 | (+8) program position at the end of current block |
Line 74: Line 74:
 | GVAR_SIMULATION_MODE | 5528 | Indicates that the machine will be in drawing mode to be able to draw/etch on the working material | | GVAR_SIMULATION_MODE | 5528 | Indicates that the machine will be in drawing mode to be able to draw/etch on the working material |
 | GVAR_SHOCK_SENSOR_IGNORE | 5529 | Ignores shock sensor data (useful when utilizing the sensors for procedures other than shock information gathering) | | GVAR_SHOCK_SENSOR_IGNORE | 5529 | Ignores shock sensor data (useful when utilizing the sensors for procedures other than shock information gathering) |
-| GVAR_STEP_PER_UNIT | 5530 | +6 Specifies the steps per unit value | +| GVAR_STEP_PER_UNIT | 5530 | (+6Specifies the steps per unit value | 
 | <del>GVAR_PARKING1</del> | 5541 | (+8) Registers are obsolete since another address space is reserved to ge up to 20 parking coordinates |  | <del>GVAR_PARKING1</del> | 5541 | (+8) Registers are obsolete since another address space is reserved to ge up to 20 parking coordinates | 
 | <del>GVAR_PARKING2</del> | 5551 | (+8) Registers are obsolete since another address space is reserved to ge up to 20 parking coordinates  | | <del>GVAR_PARKING2</del> | 5551 | (+8) Registers are obsolete since another address space is reserved to ge up to 20 parking coordinates  |
Line 83: Line 83:
 | GVAR_CURRENT_TOOLCHANGER_TYPE | 5600 | Allows to select the toolchanger type (whether it is off/linear/rotary/manual tool change) | | GVAR_CURRENT_TOOLCHANGER_TYPE | 5600 | Allows to select the toolchanger type (whether it is off/linear/rotary/manual tool change) |
 | GVAR_TOOLCHANGER_UNLOAD_OFFSET | 5601 | +8 | Specifies the offset for machine to position itself before unloading the current working tool. Typically done so that the tool is not in danger of breaking due to being pushed into the tool changer) | GVAR_TOOLCHANGER_UNLOAD_OFFSET | 5601 | +8 | Specifies the offset for machine to position itself before unloading the current working tool. Typically done so that the tool is not in danger of breaking due to being pushed into the tool changer)
-| GVAR_TOOLCHANGER_BLOW_OFF_OFFSET | 5610 | +8 The offset for the machine to position itself if the tool will be blown out by the compressed air, done for safety reasons |+| GVAR_TOOLCHANGER_BLOW_OFF_OFFSET | 5610 | (+8The offset for the machine to position itself if the tool will be blown out by the compressed air, done for safety reasons |
 | GVAR_MYDEV_MSG_COUNTER |5630 | +64 till 5694. Allows for a quick display of the number of messages in the UDP message counter field in the Network tab | | GVAR_MYDEV_MSG_COUNTER |5630 | +64 till 5694. Allows for a quick display of the number of messages in the UDP message counter field in the Network tab |
 | GVAR_TECHNOLOGY_CFG | 5701 | | GVAR_TECHNOLOGY_CFG | 5701 |
mycnc/global_variables.txt · Last modified: 2024/03/20 12:01 by ivan

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki