Differences

This shows you the differences between two versions of the page.

--- mycnc:global_variables [2019/10/15 11:15] – ivan
+++ mycnc:global_variables [2019/12/30 11:55] – ivan
@@ Line 1: / Line 1: @@
 ^ Variable Name ^ Variable Address ^ Comments ^
-|GVAR_MODAL_G0_G3 |4001 | Modal state of G00, G01, G02, G03, G33, G34 |
+|GVAR_MODAL_G0_G3 |4001 | Modal state of G00, G01, G02, G03 - motion |
-|GVAR_MODAL_G96_G97 | 4002 | Modal state of G96, G97 |
+|GVAR_MODAL2_G17_G19 | 4002 | Modal state of G17, G18, G19 - plane selection |
-|GVAR_MODAL_G68_G69 | 4004 | Modal state of G68, G69 |
+|GVAR_MODAL3_G90_G91 | 4003 | Modal state of G90, G91 - distance mode |
-|GVAR_MODAL_G98_G99 | 4005 | Modal state of G98, G99 |
+|GVAR_MODAL5_G93_G94 | 4005 | Modal state of G93, G94 - spindle speed mode |
-|GVAR_MODAL_G20_G21 | 4006 | Modal state of G20, G21 |
+|GVAR_MODAL_G20_G21 | 4006 | Modal state of G20, G21 - units |
-|GVAR_MODAL_G40_G42 | 4007 | Modal state of G40, G41, G42 |
+|GVAR_MODAL_G40_G42 | 4007 | Modal state of G40, G41, G42 - cutter diameter |
-|GVAR_MODAL_G25_G26 | 4008 | Modal state of G25, G26 |
+|GVAR_MODAL8_G43_G49 | 4008 | Modal state of G43, 49 - tool length offset |
 |GVAR_MODAL_G22_G23 | 4009 | Modal state of G22, G23 |
-|GVAR_MODAL_G80_G89 | 4010 | Modal state of G80 - G89 |
+|GVAR_MODAL10_G98_G99 | 4010 | Modal state of G98, G99 - return mode in canned cycles |
-|GVAR_MODAL_G66_G67 | 4012 | Modal state of G66, G67 |
+|GVAR_MODAL12_G54_G59 | 4012 | Modal state of G54, G55, G56, G57, G58, G59, G59.1, G59.2, G59.3 - coordinate system selection |
 |GVAR_MODAL_G54_G59 | 4014 | Modal state of G54-G59 |
 |GVAR_MODAL_G17_G19 | 4016 | Modal state of G17-G19 |
@@ Line 170: / Line 170: @@
 | GVAR_MOTION_OVERSPEED | 7072 | Register represents Motion Overrate percentage.  |
 | GVAR_SPINDLE_OVERSPEED | 7073 | Register represents Spindle Overrate percentage. \\ Actual Spindle speed will be \\ Actual_Speed=Default_Speed * Spindle_Overspeed/100 \\ Default Spindle Speed defined by "Default Spindle Speed" variable and can be chaned in G-code program with S-code.  |
-| GVAR_JOG_OVERSPEED | 7074 | The jog overspeed value is directly edited through this global variable |
+| GVAR_JOG_OVERSPEED | 7074 | The jog overspeed value is directly edited through this global variable (5-150 safe range on ET6, ET7, ET10) |
 | GVAR_PROBE_SENSOR_DIAMETER | 7075 | Specifies the probe sensor diameter in mm |
 | GVAR_PROBE_SENSOR_XOFFSET | 7076 | X-axis offset for the probe sensor in millimeters |