User Tools

Site Tools


mycnc:global_variables

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
mycnc:global_variables [2019/09/19 15:15]
ivan
mycnc:global_variables [2019/12/30 11:55] (current)
ivan
Line 1: Line 1:
 ^ Variable Name ^ Variable Address ^ Comments ^ ^ Variable Name ^ Variable Address ^ Comments ^
-|GVAR_MODAL_G0_G3 |4001 | Modal state of G00, G01, G02, G03, G33, G34 +|GVAR_MODAL_G0_G3 |4001 | Modal state of G00, G01, G02, G03 - motion ​
-|GVAR_MODAL_G96_G97 ​| 4002 | Modal state of G96G97 +|GVAR_MODAL2_G17_G19 ​| 4002 | Modal state of G17, G18G19 - plane selection ​
-|GVAR_MODAL_G68_G69 ​4004 | Modal state of G68G69 +|GVAR_MODAL3_G90_G91 ​4003 | Modal state of G90G91 - distance mode 
-|GVAR_MODAL_G98_G99 ​| 4005 | Modal state of G98G99 +|GVAR_MODAL5_G93_G94 ​| 4005 | Modal state of G93G94 - spindle speed mode 
-|GVAR_MODAL_G20_G21 | 4006 | Modal state of G20, G21 | +|GVAR_MODAL_G20_G21 | 4006 | Modal state of G20, G21 - units 
-|GVAR_MODAL_G40_G42 | 4007 | Modal state of G40, G41, G42 | +|GVAR_MODAL_G40_G42 | 4007 | Modal state of G40, G41, G42 - cutter diameter ​
-|GVAR_MODAL_G25_G26 ​| 4008 | Modal state of G25G26 |+|GVAR_MODAL8_G43_G49 ​| 4008 | Modal state of G4349 - tool length offset ​|
 |GVAR_MODAL_G22_G23 | 4009 | Modal state of G22, G23 | |GVAR_MODAL_G22_G23 | 4009 | Modal state of G22, G23 |
-|GVAR_MODAL_G80_G89 ​| 4010 | Modal state of G80 G89 +|GVAR_MODAL10_G98_G99 ​| 4010 | Modal state of G98, G99 return mode in canned cycles ​
-|GVAR_MODAL_G66_G67 ​| 4012 | Modal state of G66G67 |+|GVAR_MODAL12_G54_G59 ​| 4012 | Modal state of G54G55, G56, G57, G58, G59, G59.1, G59.2, G59.3 - coordinate system selection ​|
 |GVAR_MODAL_G54_G59 | 4014 | Modal state of G54-G59 | |GVAR_MODAL_G54_G59 | 4014 | Modal state of G54-G59 |
 |GVAR_MODAL_G17_G19 | 4016 | Modal state of G17-G19 | |GVAR_MODAL_G17_G19 | 4016 | Modal state of G17-G19 |
Line 170: Line 170:
 | GVAR_MOTION_OVERSPEED | 7072 | Register represents Motion Overrate percentage. ​ | | GVAR_MOTION_OVERSPEED | 7072 | Register represents Motion Overrate percentage. ​ |
 | GVAR_SPINDLE_OVERSPEED | 7073 | Register represents Spindle Overrate percentage. \\ Actual Spindle speed will be \\ Actual_Speed=Default_Speed * Spindle_Overspeed/​100 \\ Default Spindle Speed defined by "​Default Spindle Speed" variable and can be chaned in G-code program with S-code. ​ | | GVAR_SPINDLE_OVERSPEED | 7073 | Register represents Spindle Overrate percentage. \\ Actual Spindle speed will be \\ Actual_Speed=Default_Speed * Spindle_Overspeed/​100 \\ Default Spindle Speed defined by "​Default Spindle Speed" variable and can be chaned in G-code program with S-code. ​ |
-| GVAR_JOG_OVERSPEED | 7074 | The jog overspeed value is directly edited through this global variable |+| GVAR_JOG_OVERSPEED | 7074 | The jog overspeed value is directly edited through this global variable ​(5-150 safe range on ET6, ET7, ET10) |
 | GVAR_PROBE_SENSOR_DIAMETER | 7075 | Specifies the probe sensor diameter in mm | | GVAR_PROBE_SENSOR_DIAMETER | 7075 | Specifies the probe sensor diameter in mm |
 | GVAR_PROBE_SENSOR_XOFFSET | 7076 | X-axis offset for the probe sensor in millimeters | | GVAR_PROBE_SENSOR_XOFFSET | 7076 | X-axis offset for the probe sensor in millimeters |
Line 445: Line 445:
 | GVAR_ENCODER_Z_EVENT | 9070 | Stores info on the wheel of the encoder passing the zero mark (the zero position)| | GVAR_ENCODER_Z_EVENT | 9070 | Stores info on the wheel of the encoder passing the zero mark (the zero position)|
 | GVAR_POPUP_MESSAGE | 9100 | +16. Allows to assign popup messages with either 0 for OFF or 1 for ON (for example, 9103,1 to bring up message #3). Popup messages examples can be seen [[plc:​how_to_add_mandatory_homing_after_emergency_button_and-or_servo_ready_alarm|here]].| | GVAR_POPUP_MESSAGE | 9100 | +16. Allows to assign popup messages with either 0 for OFF or 1 for ON (for example, 9103,1 to bring up message #3). Popup messages examples can be seen [[plc:​how_to_add_mandatory_homing_after_emergency_button_and-or_servo_ready_alarm|here]].|
 +|    | 9200 | +16. Reserved to display the encoder position on an infinite scale (no value turnover on every full encoder turn, instead the value will keep climbing indefinitely into the positives/​negatives depending on where the encoder handle is spun) |
 +|    | 9216 | +16. Reserved to display the encoder position on an infinite scale WITH the current encoder dimension (to indicate the current encoder position) |
 | GVAR_SERVO_PID_ON | 60000 | Denotes that the servo PID is ON | | GVAR_SERVO_PID_ON | 60000 | Denotes that the servo PID is ON |
 | GVAR_SERVO_PID_OFF | 60001 | Denotes that the servo PID is OFF | | GVAR_SERVO_PID_OFF | 60001 | Denotes that the servo PID is OFF |
mycnc/global_variables.1568920535.txt.gz · Last modified: 2019/09/19 15:15 by ivan