mycnc:mycnc_configuration_dialogs
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
mycnc:mycnc_configuration_dialogs [2019/07/11 13:42] – ivan | mycnc:mycnc_configuration_dialogs [2019/07/12 15:49] – ivan | ||
---|---|---|---|
Line 109: | Line 109: | ||
* Press the " | * Press the " | ||
- | === Triggers === | + | === Triggers/Timers=== |
{{: | {{: | ||
+ | |||
+ | Triggers allow the software to interpret the sensor data depending on the sensor behaviour or the current position in the control program. The settings that can be assigned to the triggers are the following: | ||
+ | * Enabled/ | ||
+ | * Input number to indicate which particular input the trigger is bound to. | ||
+ | * Trigger behaviour (rising/ | ||
+ | * Output number specifies which output port is bound to the trigger prompt. This feature remains from the earlier versions of the software. | ||
+ | * Slot specifies the result of the trigger being prompted. Usually, the Stop Program option is chosen, however custom trigger responses can be written as PLC commands (such as TRIG04) | ||
+ | |||
+ | Timers serve as a way to use the controller rather than the computer for timing tasks. The following settings can be specified: | ||
+ | * Enabled/ | ||
+ | * Output pin number to specify which pin is bound to the timer | ||
+ | * Pulse time, in order to set how long the process tied to the output pin (such as a coolant system) will be ON | ||
+ | * Pause time, in order to set how long this process will be OFF | ||
=== MPG through binary inputs === | === MPG through binary inputs === | ||
{{: | {{: | ||
+ | These settings allow the user to set up the manual pulse generator behaviour. The following settings can be modified: | ||
+ | * Enabled/ | ||
+ | * Input ports number (2 ports needed for an MPG). | ||
+ | * Slot can be changed between MPG (to move the spindle around), THC/Z axis offset for manual control of the z-axis during torch height control, or Spindle Sync to synchronize the vertical z-axis movement and the rotation of the spindle. | ||
+ | * Encoder resolution: number of encoder markings per rotation * number of impulses per marking | ||
=== Jog through ADC inputs === | === Jog through ADC inputs === | ||
Line 446: | Line 464: | ||
====Camera==== | ====Camera==== | ||
{{: | {{: | ||
+ | |||
+ | For a full overview of CNC Vision Camera setup, please consult the [[quickstart: | ||
====5 axes RTCP=== | ====5 axes RTCP=== | ||
Line 470: | Line 490: | ||
===Common Hardware Settings=== | ===Common Hardware Settings=== | ||
+ | {{: | ||
===Encoders=== | ===Encoders=== | ||
+ | {{: | ||
===Analogue Closed Loop=== | ===Analogue Closed Loop=== | ||
+ | {{: | ||
===Pulse-Dir Closed Loop=== | ===Pulse-Dir Closed Loop=== | ||
+ | {{: | ||
===ET2/ | ===ET2/ | ||
+ | {{: | ||
===Host Modbus=== | ===Host Modbus=== | ||
+ | {{: | ||
====Advanced==== | ====Advanced==== | ||
===Profile=== | ===Profile=== | ||
+ | {{: | ||
===Debug=== | ===Debug=== | ||
+ | {{: | ||
===UI Settings=== | ===UI Settings=== | ||
+ | {{: | ||
mycnc/mycnc_configuration_dialogs.txt · Last modified: 2022/10/28 15:51 by ivan