mycnc:mycnc_configuration_dialogs
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
mycnc:mycnc_configuration_dialogs [2019/08/19 15:02] – ivan | mycnc:mycnc_configuration_dialogs [2019/09/03 13:54] – ivan | ||
---|---|---|---|
Line 135: | Line 135: | ||
NOTE: The ET7 controller has the two encoder slots reserved for the ET7 keyboard panel. These are permanently assigned to inputs #16, #17, #18, and #19, and changes in the Config window will not override this preset. If encoder slots are to be used on an ET7 board, the latter two are recommended. This setting is not present on the ET6/ | NOTE: The ET7 controller has the two encoder slots reserved for the ET7 keyboard panel. These are permanently assigned to inputs #16, #17, #18, and #19, and changes in the Config window will not override this preset. If encoder slots are to be used on an ET7 board, the latter two are recommended. This setting is not present on the ET6/ | ||
+ | |||
+ | NOTE #2: The ET10 controller can utilize inputs 0-31 for its binary inputs for an encoder setup. IN32-39 are reserved and are not suited for binary input configurations with an MPG wheel etc. | ||
+ | |||
+ | The full MPG though binary inputs manual is available [[mycnc: | ||
{{: | {{: | ||
Line 551: | Line 555: | ||
The colours config window allows the user to customize the visuals of the myCNC application. In this window, presets such as the dark grey and the dark blue themes can be preloaded, or customized completely from the ground up. When the user is satisfied with their particular theme, they can export it by using the Export Colors to File button. | The colours config window allows the user to customize the visuals of the myCNC application. In this window, presets such as the dark grey and the dark blue themes can be preloaded, or customized completely from the ground up. When the user is satisfied with their particular theme, they can export it by using the Export Colors to File button. | ||
+ | |||
+ | ===Visualisation Colors=== | ||
+ | |||
+ | {{: | ||
+ | |||
+ | The visualisation color settings allow the user to specify the colors that will be used in the program visualization for each of the tools in the program code. This allows the user to set each tool to an easily distinguishable color: | ||
+ | |||
+ | {{: | ||
+ | |||
+ | * Tool Number specifies the particular tool assigned to the color | ||
+ | * Width specifies the 2D width line, alpha specifies the 3D opacity (0 for transparent, | ||
+ | * Highlights are currently supported for 2D profiles only (such as plasma), and allow the user to highlight a certain tool path by clicking upon it. | ||
===Popup Messages=== | ===Popup Messages=== | ||
Line 925: | Line 941: | ||
{{: | {{: | ||
- | The Hotkeys settings window describes the possible hotkeys which are present in the software. | + | The Hotkeys settings window describes the possible hotkeys which are present in the software. These keys allow the user to control the machine directly from the keyboard, by using some commands which the user can assign to different actions. |
By default, the Shift and Control key are used to set different values of the Jog Overspeed %, allowing the user to quickly control jog speed with a single press. These can be set to be at different percentages (10 and 100 by default). | By default, the Shift and Control key are used to set different values of the Jog Overspeed %, allowing the user to quickly control jog speed with a single press. These can be set to be at different percentages (10 and 100 by default). | ||
Line 940: | Line 956: | ||
{{: | {{: | ||
- | Hardkeys allow the user to connect a button or a key to the myCNC controller which will then cause a certain event when pressed/ | + | Hardkeys allow the user to connect a button or a key directly |
* Input Number, which specifies the input to which the hardkey is connected (can be checked in the Diagnostics window) | * Input Number, which specifies the input to which the hardkey is connected (can be checked in the Diagnostics window) | ||
* Pressed/ | * Pressed/ | ||
Line 970: | Line 986: | ||
The following settings are available: | The following settings are available: | ||
- | * Encoder resolution for each particular encoder number | + | * Encoder resolution for each particular encoder number. |
- | * The current encoder value is displayed on this screen | + | * The current encoder value is displayed on this screen. This is the fastest way to check if the encoder is connected/ |
* Z-position is displayed | * Z-position is displayed | ||
- | * Mul coefficients (multiplication) | + | * Mul coefficients (multiplication |
- | * /(2^Div). These Mul and Div coefficients are used due to the fact that the controller cannot handle floating number data in calculations, | + | * /(2^Div). These Mul and Div coefficients are used due to the fact that the controller cannot handle floating number data in calculations, |
* Encoder position | * Encoder position | ||
* Position | * Position |
mycnc/mycnc_configuration_dialogs.txt · Last modified: 2022/10/28 15:51 by ivan