mycnc:mycnc_configuration_dialogs
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
mycnc:mycnc_configuration_dialogs [2019/10/22 13:20] – ivan | mycnc:mycnc_configuration_dialogs [2019/11/11 10:09] – ivan | ||
---|---|---|---|
Line 264: | Line 264: | ||
{{ mycnc: | {{ mycnc: | ||
* 2D Cutting is used on plasma/gas machines which lack a configurable z-axis. This option is turned OFF by default. | * 2D Cutting is used on plasma/gas machines which lack a configurable z-axis. This option is turned OFF by default. | ||
- | * Step-jog count specifies whether the user wants the machine to monitor the inputs sent to it as it is already moving or not. If selected, the machine will count however many signals are sent to it even if it is moving already, if not selected then the machine will ignore other signals until it has completed its initial movement. | + | * Step-jog count specifies whether the user wants the machine to monitor the inputs sent to it as it is already moving or not. If selected, the machine will count however many signals are sent to it even if it is moving already, if not selected then the machine will ignore other signals until it has completed its initial movement. This allows to set up pendant control which will either count the number of impulses sent from the pendant and move an according distance, or will instead try to match the rotation speed of the pendant wheel (moving when the wheel is moved, stopping when the wheel is stopped). |
* **Sync G0 & (G1, G2, G3) Overspeed** allows the user to sync the rapid and cutting speeds, allowing the user to use one set of buttons (shown in the screenshot below) to change them at the same time. If the check mark in the Motion configuration dialog is set to **ON**, then upon pressing the Overspeed buttons on the main screen, both G1/G2/G3 AND the G0 Overspeed will be changed (speeds will be synced). If the check mark is set to **OFF**, only the G1/G2/G3 speeds will be changed upon pressing the main screen buttons, and controlling the G0 overspeed | * **Sync G0 & (G1, G2, G3) Overspeed** allows the user to sync the rapid and cutting speeds, allowing the user to use one set of buttons (shown in the screenshot below) to change them at the same time. If the check mark in the Motion configuration dialog is set to **ON**, then upon pressing the Overspeed buttons on the main screen, both G1/G2/G3 AND the G0 Overspeed will be changed (speeds will be synced). If the check mark is set to **OFF**, only the G1/G2/G3 speeds will be changed upon pressing the main screen buttons, and controlling the G0 overspeed | ||
{{: | {{: | ||
Line 873: | Line 873: | ||
* K0 (offset value for the ratio that will bring the curve up/down) | * K0 (offset value for the ratio that will bring the curve up/down) | ||
* K (ratio value to multiply the result by) | * K (ratio value to multiply the result by) | ||
- | * P (proportional control ratio) | + | * P - proportional gain (proportional control ratio) |
- | * I (integral control ratio) | + | * I - integral gain (integral control ratio) |
- | * D (derivative control ratio) | + | * D -derivative gain (derivative control ratio) |
* Dead zone, which specifies a range in which inputs are outputted as a zero value | * Dead zone, which specifies a range in which inputs are outputted as a zero value | ||
- | * Control Min/Max | + | * Control Min/ |
- | * Sensor Offset | + | * Sensor Offset |
- | * Sensor ratio (1/1024) | + | * Sensor ratio (1/ |
+ | |||
+ | A manual on using PWM PIDs in order to control an Automatic Gas Console is available [[mycnc: | ||
==Modbus servo== | ==Modbus servo== | ||
Line 987: | Line 989: | ||
===Encoders=== | ===Encoders=== | ||
- | {{:mycnc:config-046-encoders.png}} | + | |
+ | {{:mycnc:encoders-008-config.png}} | ||
The Encoders config window allows the user to fine-tune encoder settings. This window is typically not useful for simple tasks (such as using a rotary encoder to control overspeed, etc), as it allows for further finetuning of the encoder values. | The Encoders config window allows the user to fine-tune encoder settings. This window is typically not useful for simple tasks (such as using a rotary encoder to control overspeed, etc), as it allows for further finetuning of the encoder values. | ||
The following settings are available: | The following settings are available: | ||
- | * Encoder | + | * Encoder |
* The current encoder value is displayed on this screen. This is the fastest way to check if the encoder is connected/ | * The current encoder value is displayed on this screen. This is the fastest way to check if the encoder is connected/ | ||
- | * Z-position is displayed | + | * Z-position is displayed |
- | * Mul coefficients | + | * Mul coefficients, as well as / |
- | * /(2^Div). These Mul and Div coefficients are used due to the fact that the controller cannot handle floating number data in calculations, | + | |
* Encoder position | * Encoder position | ||
* Position | * Position | ||
* Attached to motor flag (has been moved to Analog and Pulse-Dir Close Loop settings in the recent software versions). | * Attached to motor flag (has been moved to Analog and Pulse-Dir Close Loop settings in the recent software versions). | ||
- | More information on encoders is available in the [[mycnc: | + | More information on encoders is available in the [[mycnc: |
===Analogue Closed Loop=== | ===Analogue Closed Loop=== |
mycnc/mycnc_configuration_dialogs.txt · Last modified: 2022/10/28 15:51 by ivan