myCNC Online Documentation

User Tools

Site Tools

Trace:
mycnc:mycnc_et10

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
Next revisionBoth sides next revision
mycnc:mycnc_et10 [2019/02/10 19:51] – skirillovmycnc:mycnc_et10 [2019/02/10 20:16] – skirillov
Line 64: Line 64:
 === 3-wire NPN sensor connection example === === 3-wire NPN sensor connection example ===
  
-<code>Jumpers J1,J2,J3,J4 are open.</code>+<code>Jumpers are open.</code>
  
-{{hardware:et10:et10-npn-sensor-connection-001.png}}+{{hardware:et10:et10-connection-inputs-002-key-05-npn.jpg}}
  
- 
-{{hardware:et10:et10-b-connection-inputs-003.png}} 
  
 === 3-wire PNP sensor connection example === === 3-wire PNP sensor connection example ===
  
-<code>Jumpers J1,J2,J3,J4 are open.</code> +<code>Jumpers are open.</code>
- +
-{{hardware:et10:et10-pnp-sensor-connection-001.png?1000}}+
  
-{{hardware:et15-b-connection-inputs-004.png?1000}}+{{hardware:et10:et10-connection-inputs-002-key-06-pnp.jpg}}
  
  
Line 92: Line 88:
 ==== ET10 Encoder inputs ==== ==== ET10 Encoder inputs ====
  
-ET10 board has 6 Incremental encoder inputs. THere are 4 complete ABC encoder inputs (A/B quadrature encoder signals and Z signal) and 2 reduced AB encoder inputs. ET10 encoder inputs conform RS422 standard and compatible with most of servo drivers and line driver incremental encoders. 34C86 chip is used in ET10 as a receiver of encoder signals. Internal schematic for line driver encoder inputs is shown on a picture below.+ET10 board has 6 Incremental encoder inputs. There are 4 complete ABC encoder inputs (A/B quadrature encoder signals and Z signal) and 2 reduced AB encoder inputs. ET10 encoder inputs conform RS422 standard and compatible with most of the servo drivers and line driver incremental encoders. 34C86 chip is used in ET10 as a receiver of encoder signals. Internal schematic for line driver encoder inputs is shown on a picture below.
  
 **INCREMENTAL ENCODER** inputs schematic (1 Encoder, ABC signals are shown) **INCREMENTAL ENCODER** inputs schematic (1 Encoder, ABC signals are shown)
Line 102: Line 98:
 ==== ET10 DAC +/-10V DAC outputs ==== ==== ET10 DAC +/-10V DAC outputs ====
  
-ET10 control board contains 6 channel +/-10V DAC outputs. THis outputs can be used fro analgue servo ddrivers closed loop control, spindle speed control or any other application that needed in analogie signals in +/-10V range.+ET10 control board contains 6 channel +/-10V DAC outputs. This outputs can be used for analogue servo drivers closed-loop control, spindle speed control or any other application that needed in analogue signals in +/-10V range.
  
 Connectors XT16 and XT5 are used to connect DAC outputs. The connectors pinout are shown in a picture below Connectors XT16 and XT5 are used to connect DAC outputs. The connectors pinout are shown in a picture below
Line 133: Line 129:
  
  
-Connectors XT20, XT21 are used to connect ADC inputs. The connector pinout are shown below+Connectors XT20, XT21 are used to connect ADC inputs. The connector pinout is shown below
  
 {{hardware:et10:et10-connection-adc-001.jpg}} {{hardware:et10:et10-connection-adc-001.jpg}}
  
  
-The picture below shows an example for potentiometer connected to ADC2 input.+The picture below shows an example of a potentiometer connected to ADC2 input.
  
  
Line 144: Line 140:
 ==== RS422/RS485 Bus ==== ==== RS422/RS485 Bus ====
  
-A myCNC-ET10 control board has RS422/RS485 bus connector. Modbus ASCII/RTU and Hypertherm Serial communication interfaces are implemented in a myCNC-ET10 control board.+Mycnc-Et10 control board has RS422/RS485 bus connector. Modbus ASCII/RTU and Hypertherm Serial communication interfaces are implemented in myCNC-ET10 control board.
 RS422 connector pinout shown below RS422 connector pinout shown below
  
mycnc/mycnc_et10.txt · Last modified: 2023/10/25 12:59 by ivan
Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki