mycnc:mycnc_et15
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
mycnc:mycnc_et15 [2018/05/05 14:56] – skirillov | mycnc:mycnc_et15 [2020/07/06 23:18] – skirillov | ||
---|---|---|---|
Line 1: | Line 1: | ||
===== myCNC-ET15 CNC controller ===== | ===== myCNC-ET15 CNC controller ===== | ||
- | (Preview) | + | Currently, two breakout boards are available for the myCNC-ET15 controller: |
+ | |||
+ | 1) ET10/ET15 board (comes with the ET10R5C controller model) | ||
+ | |||
+ | 2) Full dedicated ET15 breakout board | ||
+ | |||
+ | Depending on the breakout board, the ET15 controller will have a different number of I/O ports. Please consult the chart below to find out the necessary model for your setup. | ||
+ | |||
+ | ^ Specs ^ Model 1 ^ Model 2 ^ | ||
+ | | Motor outputs | 6 | 8 | | ||
+ | | Pulse-dir | 6 channels, up to 3MHz | 8 channels, up to 3MHz | | ||
+ | | Analog -10V...+10V outputs | 6 channels | 8 channels | | ||
+ | | Galvanic isolated inputs | 48 | 64(72) | | ||
+ | | Encoder inputs | 4+2 channels | 8 channels | | ||
+ | | Closed loop motion control | (Pulse/ | ||
+ | | Outputs (total) | 28 | 64 | | ||
+ | | Outputs | ||
+ | | PWM outputs | 4 | 8 | | ||
+ | | RS485 Modbus | yes | yes | | ||
+ | |||
+ | //NOTE: The above information is subject to change. // | ||
+ | |||
+ | |||
==== Power supply connection ==== | ==== Power supply connection ==== | ||
Line 8: | Line 31: | ||
Power Supply 24V DC and +24V and GND pins are shown in a picture below. | Power Supply 24V DC and +24V and GND pins are shown in a picture below. | ||
- | {{hardware:et15: | + | __NOTE: The board has a set of incorrectly labelled 5V pins (labeled on the board as 24V). Below is the correct power supply pinout:__ |
+ | {{: | ||
==== Pulse-Dir outputs ==== | ==== Pulse-Dir outputs ==== | ||
Line 22: | Line 46: | ||
PULSE-DIR channels 0,1,2,3 pinout | PULSE-DIR channels 0,1,2,3 pinout | ||
- | {{hardware:et15:et15-connection-pulsedir-001.jpg}} | + | {{:mycnc: |
PULSE-DIR channels 4,5,6,7 pinout | PULSE-DIR channels 4,5,6,7 pinout | ||
- | {{hardware:et15:et15-connection-pulsedir-002.jpg}} | + | {{:mycnc: |
==== ET15 Output pins ==== | ==== ET15 Output pins ==== | ||
- | ET15 board contains | + | ET15 board contains |
- | * ... open collector outputs (OUT# | + | * 56 open collector outputs (OUT#0-OUT#55) |
- | * ... PWM outputs (PWM#1, PWM#2, PWM#3) | + | * 8 PWM outputs (PWM#0 - PWM#7) |
- | + | ||
- | < | + | |
An internal schematic is shown in the picture below. Darlington transistors array chip ULN2803 is used to buffer binary outputs in ET15. Each chip contains 8 transistors and handles 8 binary outputs. | An internal schematic is shown in the picture below. Darlington transistors array chip ULN2803 is used to buffer binary outputs in ET15. Each chip contains 8 transistors and handles 8 binary outputs. | ||
Line 41: | Line 63: | ||
ET15 pinout for outputs is shown below | ET15 pinout for outputs is shown below | ||
- | {{hardware: | + | {{:mycnc: |
==== Galvanic isolated inputs ==== | ==== Galvanic isolated inputs ==== | ||
Line 54: | Line 76: | ||
Additional 2 groups (8 optocoupler inputs) are connected to 8 encoder inputs pins (ENCODER pins 5B, 5C, 6A, 6B,6C, 7A, 7B, 7C). Change SW1 position to select either galvanic isolated inputs or line driver inputs for INPUTS # | Additional 2 groups (8 optocoupler inputs) are connected to 8 encoder inputs pins (ENCODER pins 5B, 5C, 6A, 6B,6C, 7A, 7B, 7C). Change SW1 position to select either galvanic isolated inputs or line driver inputs for INPUTS # | ||
- | + | {{:mycnc: | |
- | {{hardware:et15:et15-connection-inputs-001.jpg}} | + | |
==== ET15 Encoder inputs ==== | ==== ET15 Encoder inputs ==== | ||
Line 65: | Line 86: | ||
**ENCODERS** channels 0,1,2,3 pinout | **ENCODERS** channels 0,1,2,3 pinout | ||
- | {{hardware:et15:et15-connection-encoders-001.jpg}} | + | {{:mycnc: |
**ENCODERS** channels 4,5,6,7 pinout | **ENCODERS** channels 4,5,6,7 pinout | ||
- | {{hardware:et15:et15-connection-encoders-002.jpg}} | + | {{:mycnc: |
Line 94: | Line 115: | ||
A myCNC-ET15 control board has RS422/RS485 bus connector. Connector pinout for RS422, RS485 shown below | A myCNC-ET15 control board has RS422/RS485 bus connector. Connector pinout for RS422, RS485 shown below | ||
- | + | {{:mycnc: | |
- | {{hardware:et15:et15-connection-uart-001.jpg}} | + | |
- | + | ||
==== Connection Examples ==== | ==== Connection Examples ==== | ||
Line 389: | Line 407: | ||
http:// | http:// | ||
+ | http:// | ||
mycnc/mycnc_et15.txt · Last modified: 2022/01/28 11:21 by ivan