mycnc:mycnc_et6
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
mycnc:mycnc_et6 [2019/02/20 17:33] – skirillov | mycnc:mycnc_et6 [2019/06/11 10:13] – ivan | ||
---|---|---|---|
Line 7: | Line 7: | ||
==== Power supply connection ==== | ==== Power supply connection ==== | ||
- | 24V DC is used to supply myCNC-ET control board. Power consumption depends on external peripherals you have connected to open collector outputs and +12V/+5V outputs. Normally power supply 24V/2A should be enough to power up the controlller | + | 24V DC is used to supply myCNC-ET6 control board. Power consumption depends on external peripherals you have connected to open collector outputs and +12V/+5V outputs. Normally power supply 24V/2A should be enough to power up the controller |
{{hardware: | {{hardware: | ||
Line 101: | Line 101: | ||
==== Connection Examples ==== | ==== Connection Examples ==== | ||
- | === 3-wire NPN sensor connection example === | + | === 3-wire NPN sensor connection example |
- | {{hardware:et6-b-connection-inputs-003.png?1000}} | + | {{:mycnc:et6-npn-external-power-001.png}} |
- | === 3-wire PNP sensor connection example === | + | === 3-wire PNP sensor connection example |
+ | {{: | ||
- | {{hardware:et6-b-connection-inputs-004.png?1000}} | + | === 3-wire NPN sensor connection example (internal power supply)=== |
+ | {{:mycnc:et6-npn-internal-power-001.png}} | ||
+ | === 3-wire PNP sensor connection example (internal power supply)=== | ||
+ | {{: | ||
+ | < | ||
=== Spindle speed control through DAC (0-10V) === | === Spindle speed control through DAC (0-10V) === | ||
Line 117: | Line 122: | ||
==== ET6 control board firmware reflash ==== | ==== ET6 control board firmware reflash ==== | ||
+ | |||
{{hardware: | {{hardware: | ||
+ | |||
+ | |||
+ | myCNC-ET6 reflashing procedure may take about 3 minutes. | ||
+ | |||
+ | To reflash the board | ||
+ | - Plug 24V DC supply | ||
+ | - Plugin micro-USB cable to ET6 & Host Computer with myCNC software installed | ||
+ | - Close (short) jumpers J5(reset) & J6(programming) on myCNC control board | ||
+ | - Open (remove) J5 jumper. | ||
+ | - Open myCNC software on the Host computer, | ||
+ | - goto Configuration Tab -> Support Tab | ||
+ | - Set " | ||
+ | - Select " | ||
+ | - Set *UART port* to port with FT232 attached | ||
+ | - Set *Baud Rate* set to " | ||
+ | - Press " | ||
+ | - Sector 0 will be written at the end of process. After firmware process finished, a popup message will be shown. {{hardware: | ||
+ | - Remove all jumpers (J5, J6) and restart the board. To restart the board you need \\ either repower ET6 or \\ close Reset jumper (J5) for 1 second, then release it. The board will be restarted. | ||
+ | |||
+ | In case reflashing process failed, you get a popup message. {{hardware: | ||
+ | |||
+ | |||
+ | |||
+ | |||
mycnc/mycnc_et6.txt · Last modified: 2023/03/16 09:23 by ivan