User Tools

Site Tools


mycnc:mycnc_et6

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
Next revisionBoth sides next revision
mycnc:mycnc_et6 [2019/06/11 11:33] ivanmycnc:mycnc_et6 [2020/03/27 09:27] ivan
Line 3: Line 3:
 ==== ET6 Top View ==== ==== ET6 Top View ====
  
-{{hardware:et6:et6-101-1280.jpg}}+{{:mycnc:001-et6-101-1280.jpg}}
  
 ==== Power supply connection ==== ==== Power supply connection ====
Line 9: Line 9:
 24V DC is used to supply myCNC-ET6 control board. Power consumption depends on external peripherals you have connected to open collector outputs and +12V/+5V outputs. Normally power supply 24V/2A should be enough to power up the controller based kit with single board computer and 15'6" TFT screen. However, step-down converters on the ET6 board consume start current about 1.5A and 24V/1A power supply might be not enough to supply the single ET6 board. 24V DC is used to supply myCNC-ET6 control board. Power consumption depends on external peripherals you have connected to open collector outputs and +12V/+5V outputs. Normally power supply 24V/2A should be enough to power up the controller based kit with single board computer and 15'6" TFT screen. However, step-down converters on the ET6 board consume start current about 1.5A and 24V/1A power supply might be not enough to supply the single ET6 board.
  
-{{hardware:et6:et6-power-connection-001.jpg}}+{{:mycnc:002-et6-power-connection-001.jpg}}
  
  
Line 22: Line 22:
  
 Pulse-Dir connectors pinout shown below Pulse-Dir connectors pinout shown below
-{{hardware:et6:et6-pulse-dir-connection-001.jpg}}+{{:mycnc:003-et6-pulse-dir-connection-001.jpg}}
  
- +{{:mycnc:004-et6-stepper-motors-001.jpg}}
-{{:mycnc:et6-stepper-motors-001.png}}+
  
 ==== ET6 Output pins ==== ==== ET6 Output pins ====
Line 34: Line 33:
   * 3 PWM outputs (PWM#1, PWM#2, PWM#3)   * 3 PWM outputs (PWM#1, PWM#2, PWM#3)
  
-<code>WARNING: ET6 board rev.1 has Output pin names printed on Botton side of the board.  +<code>WARNING: ET6 board rev.1 has Output pin names printed on Bottom side of the board.  
-This names are NOT correct and differs from actual output addresses.  +This names are NOT correct and differ from actual output addresses.  
-Please check table below to find out actual output address</code>+Please check table below to find out actual output addresses</code>
  
  
Line 58: Line 57:
 Connector pinouts for ET6 outputs pin shown on a picture below Connector pinouts for ET6 outputs pin shown on a picture below
  
-{{hardware:et6:et6-outputs-connection-001.jpg}}+{{:mycnc:005-et6-outputs-connection-001.jpg}}
  
 ==== Galvanic isolated inputs ==== ==== Galvanic isolated inputs ====
Line 69: Line 68:
  
 Connector pinouts for ET6 galvanic isolated inputs shown on a picture below Connector pinouts for ET6 galvanic isolated inputs shown on a picture below
-{{hardware:et6:et6-inputs-connection-001.jpg}}+{{:mycnc:007-et6-inputs-connection-001.jpg}}
  
  
Line 81: Line 80:
  
 RS485 connector pinout shown below: RS485 connector pinout shown below:
- +{{:mycnc:009-et6-rs485-connection-001.jpg}}
-{{hardware:et6:et6-rs485-connection-001.jpg}} +
  
 ==== DAC output ==== ==== DAC output ====
Line 95: Line 92:
  
 Connector pinout for DAC output: Connector pinout for DAC output:
-{{hardware:et6:et6-dac-connection-001.jpg}}+{{:mycnc:011-et6-dac-connection-001.jpg}}
  
  
Line 101: Line 98:
 === 3-wire NPN sensor connection example (external power supply)=== === 3-wire NPN sensor connection example (external power supply)===
  
-{{:mycnc:et6-npn-external-power-001.png}}+{{:mycnc:012-et6-npn-external-power-001-v2.jpg}}
  
 === 3-wire PNP sensor connection example (external power supply)=== === 3-wire PNP sensor connection example (external power supply)===
-{{:mycnc:et6-pnp-external-power-001.png}}+{{:mycnc:013-et6-pnp-external-power-001-v2.jpg}}
  
 === 3-wire NPN sensor connection example (internal power supply)=== === 3-wire NPN sensor connection example (internal power supply)===
-{{:mycnc:et6-npn-internal-power-001.png}}+{{:mycnc:014-et6-npn-internal-power-001-v2.jpg}}
  
 === 3-wire PNP sensor connection example (internal power supply)=== === 3-wire PNP sensor connection example (internal power supply)===
-{{:mycnc:et6-pnp-internal-power-001.png}}+{{:mycnc:015-et6-pnp-internal-power-001-v2.jpg}}
  
-<code>Depending on the particular sensor, power can be supplied through any of the power input connections (5V, 12V, 24V). 24V was chosen in these examples as it is the industry standard.</code>+<code>Depending on the particular sensor, power can be supplied through  
 +any of the power input connections (5V, 12V, 24V).  
 +24V was chosen in these examples as it is the industry standard.</code>
  
 === Spindle speed control through DAC (0-10V) === === Spindle speed control through DAC (0-10V) ===
  
-{{:mycnc:et6-spindle-001.png}}+{{:mycnc:016-et6-spindle-001.jpg}}
  
 ===Switch connection example (external power supply)=== ===Switch connection example (external power supply)===
-{{:mycnc:et6-switch-external-001.png}}+{{:mycnc:017-et6-switch-external-001-v2.jpg}}
  
-{{:mycnc:et6-switch-external-002.png}}+{{:mycnc:018-et6-switch-external-002-v2.jpg}}
  
 ==== ET6 control board firmware reflash ==== ==== ET6 control board firmware reflash ====
  
- +{{:mycnc:019-et6-reflash-001.jpg}}
-{{hardware:et6:et6-reflash-001.jpg}}+
  
  
mycnc/mycnc_et6.txt · Last modified: 2023/03/16 09:23 by ivan

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki