mycnc:mycnc_rotate_widget
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
mycnc:mycnc_rotate_widget [2018/07/20 12:38] – pupalaiser | mycnc:mycnc_rotate_widget [2019/10/31 12:04] – ivan | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | **MyCNC Rotete | + | ======MyCNC Rotation |
- | **aaaaa** | + | Below is the main screen of the rotation widget: |
+ | {{: | ||
- | ^Katya^Ilya^ | + | // |
- | |bejfvrwljtbrknbltnytohyn|bjrlfbegbrtjknbteyk| | + | {{:mycnc:rotation-widget-002-tooltips.png}} |
- | {{ : | + | |{{:mycnc:rotation-widget-006-button-refresh.png}}|Refresh |
- | + | |{{:mycnc:rotation-widget-007-button-x.png}}|Move along the X axis to the specified | |
- | {{ : | + | |{{:mycnc:rotation-widget-008-button-y.png}}|Move along the Y axis to the specified |
- | //**Basic functions.**// | + | |
- | {{ :mycnc:rotate_1.png? | + | |
- | | {{: | + | |
- | |{{:mycnc:x_.png?60|}}|Moving | + | |
- | |{{:mycnc:y_.png?60|}}|Moving | + | |
// | // | ||
- | {{ :mycnc:2018-05-30_17-33-06.jpg? | + | {{:mycnc:rotation-widget-009-vertical.png}} |
- | | {{ : | + | | {{ : |
- | // | + | // |
- | {{ :mycnc:2018-05-30_17-33-48.jpg? | + | {{:mycnc:rotation-widget-010-horizontal.png}} |
- | | {{ : | + | | {{ : |
- | **// | + | **// |
- | {{ :mycnc:2018-05-30_17-34-10.jpg? | + | {{:mycnc:rotation-widget-011-xy.png}} |
- | |{{ : | + | |{{ : |
- | **//Rotate | + | **//Rotation of the nesting map to some specified angle//** |
- | {{:mycnc:rotate_6.png?1000|}} | + | {{:mycnc:rotation-widget-012-enter-angle-popup.png}} |
- | //To cut the corrected nesting chart, it is necessary to press the send button | + | //To be able to use the corrected nesting chart, it is necessary to press the Send button |
- | {{:mycnc:rotate_7.png?1000|}} | + | {{:mycnc:rotation-widget-013-send.png}} |
- | **//Correction of the position | + | **//Sheet position |
- | //Setting | + | //Set the first point. |
- | {{:mycnc:rotate_2.png?1000|}} | + | {{:mycnc:rotation-widget-014.png}} |
- | //Next, move the plasma torch along the sheet (the longer the movement, the more accurate the correction will be). We bring the plasmatron | + | //Next, move the plasma torch along the sheet (the longer the distance of this movement, the more accurate the correction will be). We bring the plasma torch to the edge of the sheet after moving along it. We assign this second point by pressing the " |
- | {{:mycnc:rotate_3.png?1000|}} | + | {{:mycnc:rotation-widget-015.png}} |
- | //After clicking on the "confirmation confirmation" button, you must confirm the conversion in the appeared | + | //After clicking on the "Apply Correction" button, you must confirm the program |
- | {{:mycnc:rotate_4.png?1000|}} | + | {{:mycnc:rotation-widget-016.png}} |
- | //After confirmation, | + | // |
- | {{:mycnc:rotate_5.png?1000|}} | + | {{:mycnc:rotation-widget-017.png}} |
- | **//Turning | + | **//Rotation of the nesting map to a previously used angle//** |
- | // | + | //Select the rotation angle from the list of previously used values// |
- | {{:mycnc:rotate_8.png?1000|}} | + | {{:mycnc:rotation-widget-018.png}} |
- | //Confirm or cancel the correction// | + | //Confirm or cancel the rotation// |
- | {{:mycnc:rotate_9.png?1000|}} | + | {{:mycnc:rotation-widget-019.png}} |
- | //To cut the corrected nesting chart, it is necessary to press the send button | + | //After the changes have been applied, it is necessary to press the Send button |
- | {{:mycnc:rotate_10.png?1000|}} | + | {{:mycnc:rotation-widget-020.png}} |
mycnc/mycnc_rotate_widget.txt · Last modified: 2022/02/08 16:36 by ivan