mycnc:mycnc_rotate_widget
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
mycnc:mycnc_rotate_widget [2019/10/31 08:56] – ivan | mycnc:mycnc_rotate_widget [2019/10/31 12:04] – ivan | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | **MyCNC Rotation Widget. Main window.** | + | ======MyCNC Rotation Widget====== |
- | {{ :mycnc:2018-05-25_14-39-01.jpg? | + | |
- | //**Basic rotation widget functions.**// | + | Below is the main screen of the rotation widget: |
- | {{ :mycnc:rotate_1.png? | + | {{:mycnc:rotation-widget-001-main-screen.png}} |
- | | {{: | + | |
- | |{{:mycnc:x_.png?60|}}|Move along the X axis to the specified value|{{: | + | //**Basic rotation widget functions:**// |
- | |{{:mycnc:y_.png?60|}}|Move along the Y axis to the specified value|{{: | + | {{:mycnc:rotation-widget-002-tooltips.png}} |
+ | |{{:mycnc:rotation-widget-006-button-refresh.png}}|Refresh the nesting chart (visual display) | ||
+ | |{{:mycnc:rotation-widget-007-button-x.png}}|Move along the X axis to the specified value|{{: | ||
+ | |{{:mycnc:rotation-widget-008-button-y.png}}|Move along the Y axis to the specified value|{{: | ||
// | // | ||
- | {{ :mycnc:2018-05-30_17-33-06.jpg? | + | {{:mycnc:rotation-widget-009-vertical.png}} |
| {{ : | | {{ : | ||
- | // | + | // |
- | {{ :mycnc:2018-05-30_17-33-48.jpg? | + | {{:mycnc:rotation-widget-010-horizontal.png}} |
| {{ : | | {{ : | ||
**// | **// | ||
- | {{ :mycnc:2018-05-30_17-34-10.jpg? | + | {{:mycnc:rotation-widget-011-xy.png}} |
|{{ : | |{{ : | ||
- | **//Rotate | + | **//Rotation of the nesting map to some specified angle//** |
- | {{:mycnc:rotate_6.png?1000|}} | + | {{:mycnc:rotation-widget-012-enter-angle-popup.png}} |
- | //To be able to use the corrected nesting chart, it is necessary to press the send button | + | //To be able to use the corrected nesting chart, it is necessary to press the Send button |
- | {{:mycnc:rotate_7.png?1000|}} | + | {{:mycnc:rotation-widget-013-send.png}} |
**//Sheet position correction by using two points//** | **//Sheet position correction by using two points//** | ||
//Set the first point. Position the plasma torch at the lower left corner of the sheet. The point is recorded by pressing the " | //Set the first point. Position the plasma torch at the lower left corner of the sheet. The point is recorded by pressing the " | ||
- | {{:mycnc:rotate_2.png?1000|}} | + | {{:mycnc:rotation-widget-014.png}} |
//Next, move the plasma torch along the sheet (the longer the distance of this movement, the more accurate the correction will be). We bring the plasma torch to the edge of the sheet after moving along it. We assign this second point by pressing the " | //Next, move the plasma torch along the sheet (the longer the distance of this movement, the more accurate the correction will be). We bring the plasma torch to the edge of the sheet after moving along it. We assign this second point by pressing the " | ||
- | {{:mycnc:rotate_3.png?1000|}} | + | {{:mycnc:rotation-widget-015.png}} |
//After clicking on the "Apply Correction" | //After clicking on the "Apply Correction" | ||
- | {{:mycnc:rotate_4.png?1000|}} | + | {{:mycnc:rotation-widget-016.png}} |
- | //After confirmation, | + | // |
- | {{:mycnc:rotate_5.png?1000|}} | + | {{:mycnc:rotation-widget-017.png}} |
- | **//Turning | + | **//Rotation of the nesting map to a previously used angle//** |
- | // | + | //Select the rotation angle from the list of previously used values// |
- | {{:mycnc:rotate_8.png?1000|}} | + | {{:mycnc:rotation-widget-018.png}} |
- | //Confirm or cancel the correction// | + | //Confirm or cancel the rotation// |
- | {{:mycnc:rotate_9.png?1000|}} | + | {{:mycnc:rotation-widget-019.png}} |
- | //To cut the corrected nesting chart, it is necessary to press the Send button to display the corrected | + | //After the changes have been applied, it is necessary to press the Send button to display the rotated |
- | {{:mycnc:rotate_10.png?1000|}} | + | {{:mycnc:rotation-widget-020.png}} |
mycnc/mycnc_rotate_widget.txt · Last modified: 2022/02/08 16:36 by ivan