User Tools

Site Tools


mycnc:mycnc_setup_examples:plasma_cutting:1366p

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
mycnc:mycnc_setup_examples:plasma_cutting:1366p [2019/10/10 11:15] ivanmycnc:mycnc_setup_examples:plasma_cutting:1366p [2020/11/11 11:49] (current) ivan
Line 47: Line 47:
 |{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-037-reset-beginning.jpg}}| Reset the operating point to the beginning of control program | |{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-037-reset-beginning.jpg}}| Reset the operating point to the beginning of control program |
 |{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-038-return-working-point.jpg}}| Return to the working point | |{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-038-return-working-point.jpg}}| Return to the working point |
-|{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-039-bring-start-operating-point.jpg}}| Binding of the start of the control program to operating point|+|{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-039-bring-start-operating-point.jpg}}| Binding of the start of the control program to operating point. NOTE: The machine will bind the coordinates for the axes specified in Settings > Config > Preferences > Start/Stop. If no axes are selected, no binding to the operating point will be performed. Link to video with demo: https://www.youtube.com/watch?v=lgKgMRz-JN8&feature=youtu.be&t=45 |
 |{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-040.jpg}}| Start cutting from this position | |{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-040.jpg}}| Start cutting from this position |
-|{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-041.jpg}}| Enter simulation mode (ignore cutting commands- see below|+|{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-041.jpg}}| Enter simulation mode (trial mode) to ignore cutting commands - see description below|
  
 |{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-042-go-back.jpg}} | Go back | |{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-042-go-back.jpg}} | Go back |
Line 56: Line 56:
 |{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-042-go-back.jpg}} | Go back | |{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-042-go-back.jpg}} | Go back |
 |{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-043-stop.jpg}} | Stop the program | |{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-043-stop.jpg}} | Stop the program |
-|{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-052-laser-pointer.jpg}}| Switch the instrument to laser pointer |+|{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-052-laser-pointer.jpg}}| Switch the instrument to laser pointer. Link to video with demo: https://www.youtube.com/watch?v=pxMQ9XLyOBQ |
  
 ====G-code tab (Part selection and editing)==== ====G-code tab (Part selection and editing)====
Line 72: Line 72:
 This screen presents the user with the options and indicators for the plasma controls. The five buttons on the right side of the tab are the most commonly used: This screen presents the user with the options and indicators for the plasma controls. The five buttons on the right side of the tab are the most commonly used:
  
-| {{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-057-surface-measure.jpg}}    +|{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-057-surface-measure.jpg}}| Surface Measure  
-| {{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-058-plasma-on.jpg}} |  +|{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-058-plasma-on.jpg}}| Plasma ON 
-| {{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-059-xyz-homing.jpg}}   +|{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-059-xyz-homing.jpg}}| Homing for the XYZ axes 
-| {{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-060-servo-on.jpg}} |  +|{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-060-servo-on.jpg}}| Servo ON (done through software PLC) 
-| {{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-061-servo-off.jpg}} |  |+|{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-061-servo-off.jpg}}| Servo OFF |
  
  
Line 113: Line 113:
 {{:mycnc:mycnc_setup_examples:plasma_cutting:plasma-progress-bar-setting-002.png}} {{:mycnc:mycnc_setup_examples:plasma_cutting:plasma-progress-bar-setting-002.png}}
  
-====Simulation mode - ignore cutting commands====+====Simulation mode (Trial mode) ====
  
 With the simulation mode turned ON, the software will ignore the cutting commands, simply moving the working bit (plasma torch, laser pointer, etc) around to give the user an option of running the program before the actual cutting begins. The commands which the myCNC software will ignore can be specified in the **Settings > Config > Preferences > Start/Stop**, as seen in the image below: With the simulation mode turned ON, the software will ignore the cutting commands, simply moving the working bit (plasma torch, laser pointer, etc) around to give the user an option of running the program before the actual cutting begins. The commands which the myCNC software will ignore can be specified in the **Settings > Config > Preferences > Start/Stop**, as seen in the image below:
  
 {{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-on-off-commands-001.png}} {{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-on-off-commands-001.png}}
mycnc/mycnc_setup_examples/plasma_cutting/1366p.1570720555.txt.gz · Last modified: 2019/10/10 11:15 by ivan

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki