User Tools

Site Tools


mycnc:mycnc_setup_examples:plasma_cutting:1366p

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
mycnc:mycnc_setup_examples:plasma_cutting:1366p [2019/10/10 11:17]
ivan
mycnc:mycnc_setup_examples:plasma_cutting:1366p [2019/10/22 13:22] (current)
ivan
Line 47: Line 47:
 |{{:​mycnc:​mycnc_setup_examples:​plasma_cutting:​screen-1366p-037-reset-beginning.jpg}}| Reset the operating point to the beginning of control program | |{{:​mycnc:​mycnc_setup_examples:​plasma_cutting:​screen-1366p-037-reset-beginning.jpg}}| Reset the operating point to the beginning of control program |
 |{{:​mycnc:​mycnc_setup_examples:​plasma_cutting:​screen-1366p-038-return-working-point.jpg}}| Return to the working point | |{{:​mycnc:​mycnc_setup_examples:​plasma_cutting:​screen-1366p-038-return-working-point.jpg}}| Return to the working point |
-|{{:​mycnc:​mycnc_setup_examples:​plasma_cutting:​screen-1366p-039-bring-start-operating-point.jpg}}| Binding of the start of the control program to operating point|+|{{:​mycnc:​mycnc_setup_examples:​plasma_cutting:​screen-1366p-039-bring-start-operating-point.jpg}}| Binding of the start of the control program to operating point. NOTE: The machine will bind the coordinates for the axes specified in Settings > Config > Preferences > Start/Stop. If no axes are selected, no binding to the operating point will be performed. ​|
 |{{:​mycnc:​mycnc_setup_examples:​plasma_cutting:​screen-1366p-040.jpg}}| Start cutting from this position | |{{:​mycnc:​mycnc_setup_examples:​plasma_cutting:​screen-1366p-040.jpg}}| Start cutting from this position |
-|{{:​mycnc:​mycnc_setup_examples:​plasma_cutting:​screen-1366p-041.jpg}}| Enter simulation mode (ignore cutting commands- see below|+|{{:​mycnc:​mycnc_setup_examples:​plasma_cutting:​screen-1366p-041.jpg}}| Enter simulation mode (trial mode) to ignore cutting commands - see description ​below|
  
 |{{:​mycnc:​mycnc_setup_examples:​plasma_cutting:​screen-1366p-042-go-back.jpg}} | Go back | |{{:​mycnc:​mycnc_setup_examples:​plasma_cutting:​screen-1366p-042-go-back.jpg}} | Go back |
Line 113: Line 113:
 {{:​mycnc:​mycnc_setup_examples:​plasma_cutting:​plasma-progress-bar-setting-002.png}} {{:​mycnc:​mycnc_setup_examples:​plasma_cutting:​plasma-progress-bar-setting-002.png}}
  
-====Simulation mode - ignore cutting commands====+====Simulation mode (Trial mode) ====
  
 With the simulation mode turned ON, the software will ignore the cutting commands, simply moving the working bit (plasma torch, laser pointer, etc) around to give the user an option of running the program before the actual cutting begins. The commands which the myCNC software will ignore can be specified in the **Settings > Config > Preferences > Start/​Stop**,​ as seen in the image below: With the simulation mode turned ON, the software will ignore the cutting commands, simply moving the working bit (plasma torch, laser pointer, etc) around to give the user an option of running the program before the actual cutting begins. The commands which the myCNC software will ignore can be specified in the **Settings > Config > Preferences > Start/​Stop**,​ as seen in the image below:
  
 {{:​mycnc:​mycnc_setup_examples:​plasma_cutting:​screen-1366p-on-off-commands-001.png}} {{:​mycnc:​mycnc_setup_examples:​plasma_cutting:​screen-1366p-on-off-commands-001.png}}
mycnc/mycnc_setup_examples/plasma_cutting/1366p.1570720667.txt.gz ยท Last modified: 2019/10/10 11:17 by ivan