Differences

This shows you the differences between two versions of the page.

--- mycnc:wireless_pendants [2019/07/26 10:16] – ivan
+++ mycnc:wireless_pendants [2019/07/26 11:23] – ivan
@@ Line 33: / Line 33: @@
 | Hardware: Direct DAC Set |  |
 | Hardware: Direct PWM Set |  |
-| Hide: Custom Widget by name |  |
+| Hide: Custom Widget by name | Hide the custom widget |
-| Job: Play 1 line |  |
+| Job: Play 1 line | Run through a single command line (next line) |
-| Job: Play 1 line backwards |  |
+| Job: Play 1 line backwards | Run through a single command line (previous line) |
 | Job: Back to path | Return back to the cutting path |
-| Job: Skip forward |  |
+| Job: Skip forward | Move forward in the command program |
-| Job: Skip backward |  |
+| Job: Skip backward | Move backward in the command program |
 | Job: Skip forward 10 | Skip 10 lines forward |
 | Job: Skip backward 10 | Skip 10 lines backward |
@@ Line 60: / Line 60: @@
 | Key release | Simulates a key release |
 | (Dlg)Key Press | Simulates a dialog key press, such as Shift, Enter, Delete, 0-9, etc |
-| Move to toolpath |  |
+| Move to toolpath | Move back to the toolpath |
 | Parking position: Save | Save the current position as the parking position |
 | Parking position: Move to | Move to the parking position |
 | Pendant: Axis (*) |  |
 | Pendant: Mul (*) |  |
-| Pendant: Wheel CW |  |
+| Pendant: Wheel CW | Record the input as wheel moving clockwise |
-| Pendant: Wheen CCW |  |
+| Pendant: Wheel CCW | Record the input as wheel moving counter-clockwise |
 | Pendant: Mul increment |  |
 | Pendant: Mul decrement |  |
 | Pendant: Axis change + |  |
 | Pendant: Axis change - |  |
-| Pendant0: x0.001-1 |  |
+| Pendant0: x0.001-1 | Sets the increment for the machine movements which is controlled by the pendant |
 | Pendant0: Axis off |  |
-| Pendant0: Axis X-C |  |
+| Pendant0: Axis X-C | Sets the axis that the pendant will be sending commands to |
-| Pendant: Work coordinate Half |  |
+| Pendant: Work coordinate Half | Takes the pendant work coordinate (in the axis specified on the pendant) and halves it |
-| Pendant: Work coordinate Reset |  |
+| Pendant: Work coordinate Reset | Resets the work coordinate specified in the pendant axis |
 | PLC: Run procedure | Run a PLC procedure |
 | PLC: Run external unit procedure | Run a PLC procedure on a slave controller. The syntax for the command will be as follows: controller number / command / variable (for example, 0x01/M74/#7009) |
 | Run Numpad |  |
-| Show: Pendant control widget |  |
+| Show: Pendant control widget | Brings up the pendant control widget in the myCNC software |
 | Select axis | Select the particular axis |
 | Show: Widget | Shows a particular widget, such as Library Shape, Diagnostics, Config, etc |
@@ Line 87: / Line 87: @@
 | Spindle Speed: inc | Increase the current spindle speed |
 | Spindle Speed: dec | Decrease the current spindle speed |
-| Spindle Speed: set | Set the spindle speed |
+| Spindle Speed: set | Set the current spindle speed |
 | Tie Toolpath Position to current work position |  |
 | Toggle Machine/Work DRO (if applicable) |  |
 | Toggle Jog enable/disable | Turn jog on and off |
-| Toggle Jog mode unlimited/step | Switch between  |
+| Toggle Jog mode unlimited/step | Switch between the unlimited and a set step jog for machine movements |
 | Toggle Soft Limits enable/disable | Turn the soft limits (specified in Inputs/Outputs/Sensors > Limits) on and off |
 | Toggle Flood on/off | Turns the liquid cooling (flood) on and off |
@@ Line 98: / Line 98: @@
 | Toggle Constant Velocity on/off | CV (constant velocity) is described in [[mycnc:constant_velocity_mode_cv|MyCNC Constant Velocity Mode (CV)]] manual |
 | Toggle Virtual Keyboard | Brings up the virtual keyboard up on the screen, or hides it if already present |
-| Toggle: custom widget by name |  |
+| Toggle: custom widget by name | Specifies a custom widget to bring up on the screen (or close it if already displayed). The syntax for this will be as follows:  |
 | View: Zoom In | Zoom in on the control program visualization |
 | View: Zoom Out | Zoom out on the control program visualization |
 | View: Fit to window | Fit the entire visualization into the window |
-| Work coordinate: Set | Set the work coordinate |
+| Work coordinate: Set | Set the work coordinate (using the specified user panel axis) |
-| Work coordinate: Reset | Reset the work coordinate |
+| Work coordinate: Reset | Reset the work coordinate (from user panel) |
-| Work Coordinate: 1/2 | Half the work coordinate |
+| Work Coordinate: 1/2 | Half the work coordinate (from user panel) |