Differences

This shows you the differences between two versions of the page.

--- mycnc:wireless_pendants [2019/07/26 11:36] – ivan
+++ mycnc:wireless_pendants [2019/07/26 12:35] – ivan
@@ Line 1: / Line 1: @@
-=====Wireless Pendants=====
+ =====Wireless Pendants=====
 Wireless pendants are currently sold in three configurations in the myCNC Shop.
@@ Line 28: / Line 28: @@
 | File: Open DXF/HPGL | Open a DXF/HPGL file from the folders specified in Preferences > Common |
 | File: Refresh | Refresh the program file |
-| Hardware: Direct Binary Set |  |
+| Hardware: Direct Binary Set | Directly sets a binary to be ON |
-| Hardware: Direct Binary Clear |  |
+| Hardware: Direct Binary Clear | Sets a binary to be OFF |
-| Hardware: Direct DAC Set |  |
+| Hardware: Direct DAC Set | Sets the DAC |
-| Hardware: Direct PWM Set |  |
+| Hardware: Direct PWM Set | Sets the Pulse Width Modulation |
 | Hide: Custom Widget by name | Hide the custom widget |
 | Job: Play 1 line | Run through a single command line (next line) |
@@ Line 48: / Line 48: @@
 | Jog: X+ Y+ | Jog in the positive x, positive y direction |
 | Jog: All stop | Stop jog for all axes |
-| Jog: Shift Set |  |
+| Jog: Shift Set | Jog: Shift and Jog: Ctrl both refer to the settings window in Panel/Pendant > Hotkeys. The shift set indicates that the Shift button has been pressed |
-| Jog: Shift Clear |  |
+| Jog: Shift Clear | Indicates that the shift button has been released |
-| Jog: Shift Toggle |  |
+| Jog: Shift Toggle | Toggles the shift button on and off |
-| Jog: Ctrl Set |  |
+| Jog: Ctrl Set | Indicates that the control button has been pressed |
-| Jog: Ctrl Clear |  |
+| Jog: Ctrl Clear | Indicates that the control button has been released |
-| Jog: Ctrl Toggle |  |
+| Jog: Ctrl Toggle | Toggles the control button |
 | Jog Override: inc | Increase the jog override |
 | Jog Override: dec | Decrease the jog override |
@@ Line 62: / Line 62: @@
 | Parking position: Save | Save the current position as the parking position |
 | Parking position: Move to | Move to the parking position |
-| Pendant: Axis (*) |  |
+| Pendant: Axis (*) | Switches through all the available axis values on repeat (continuously looping through the values as the button is pressed) |
-| Pendant: Mul (*) |  |
+| Pendant: Mul (*) | Switches through all available step size values on repeat (continuously looping through the available step size values) |
 | Pendant: Wheel CW | Record the input as wheel moving clockwise |
 | Pendant: Wheel CCW | Record the input as wheel moving counter-clockwise |
@@ Line 87: / Line 87: @@
 | Spindle Speed: dec | Decrease the current spindle speed |
 | Spindle Speed: set | Set the current spindle speed |
-| Tie Toolpath Position to current work position |  |
+| Tie Toolpath Position to current work position | Used on control programs with a large number of parts, this allows to tie the toolpath position to the current work position. Effectively, this allows to cut out a small part of the control program anywhere on the sheet, by simply specifying the position of the toolpath |
-| Toggle Machine/Work DRO (if applicable) |  |
+| Toggle Machine/Work DRO (if applicable) | A setting for pendants which only show one coordinate system at a time (machine or program coordinate). This allows to switch between the two coordinate systems - used only on select controllers. |
 | Toggle Jog enable/disable | Turn jog on and off |
 | Toggle Jog mode unlimited/step | Switch between the unlimited and a set step jog for machine movements |