Fulltext results:
- global_variables
- Global Variables====== ^ Related articles ^ | [[plc:plc|PLC]] | | [[mycnc:global_variables_description|Global Variables Description]] | ----- ^ Variable Nam... Specifies the steps per unit value | | GVAR_SET_PLC_MOVE_VERSION | 5539 | A new version of g0moveA, c
- height_mapping
- ht Mapping====== // **Related articles:**// * [[plc:plc_height_map|Getting a Height Map]] ---- <code>ATTENTION: Height mapping is currently in beta test... file. * Head into myCNC ''Settings > Config > PLC > Hardware PLC'' and add the ''M180'' procedure if it is not already present. * On recent softwar
- edge_detection
- manual, we will be describing the ways in which a PLC designed for locating the edges of the working ma... edges of the working material Note that the M190.plc code is specific to a particular application that... tion of the working material edges: <code C M190.plc> //#include pins.h #define INPUT_PROBE 13 #def... cedure is done for the Y direction. In the M190.plc code above, variables "x0" and "y0" are used, whi
- axis_plus
- control and positioning instructions from within PLC commands. This functionality useful for applicat... Automatic Z-axis Homing procedure: <code C M133.plc>#include pins.h main() { gvarset(5521,1); //Ig... 3 (Manual Z-axis Homing) procedure: <code C M143.plc>main() { if (eparam==0) { gvarset(5521,1)... et Soft Limit + (Plus) | ====Position command (PLC)==== ^ Register ^ Access ^ Description ^ | 8
- stop_end_program
- ssed are defined in the following files: * M02.plc (Settings > Config > PLC > Hardware PLC) * OFF.plc (Settings > Config > PLC > Hardware PLC) * %%__HANDLER_GCODE_STOP%% (Settings > Config
- mycnc_setup_examples
- ribed on "pins.h" includes the file in **Hardware PLC Builder** area - <code C pins.h>//input/output ... gnal inverted) if Bit #4 is set. This way we add PLC procedures M201 and M202 to switch Z axis between Motor outputs #3 and #4 <code C M201.plc>#include vars.h main() { parameter=15; //OFF ... e(timer>0); exit(99); }; </code> <code C M202.plc>#include vars.h main() { parameter=15; //OFF
- laser_cutting
- ould be redefined via the global variables from a PLC only in certain special applications. Writing a ... lue to the Global variable register from Hardware PLC procedure will change Frequency of PWM outputs. T... he calibration process is implemented in the M275 PLC procedure. The procedure consists of the followi... libration procedure is shown below: <code C M275.plc> #include vars.h #include pins.h do_laser_probi
- 20000-20100 @mycnc:global_variables
- ====== PLC program diagnostics via Debug Messages ====== When diagnosing the way in which a PLC program operates (for instance, checking some values from an arbitrary point within the PLC code, making sure the final output values are correct, correcting PLC logic, etc), it is often useful to utilize the de
- rtcp_setup
- ot be changed while RTCP switching. We used M101.plc procedure to disable(**OFF**) RTCP correction <code C M101.plc> #include pins.h #include vars.h main() { time... );//50msec pause exit(99); }; </code> and M102.plc procedure to enable(**ON**) RTCP correction <code C M102.plc> #include pins.h #include vars.h main() { time
- m6_tool_change_macro @mycnc:m6_tool_change_macro
- output 1/2 are turned on/off). M62 is a Hardware PLC procedure which turns a select port ON, while M63
- gcodes_list
- ns have been largely replaced and expanded by the PLC commands (specific probing M-codes) | | G38.3 | G... | <del>Pause</del> | | | | M01 | Optional Stop | PLC | | | M02 | End Program | Native + PLC | | | M03 | Spindle On CW | PLC | | | M04 | Spindle On CCW | PLC | | | M05 | Spindle Stop | PLC | | |
- mycnc_screen_configuration
- h="70" height="70" image="M/button-m03" action="plc-run:M03/#5524" type="xbutton" /> </code> Attr... \ or through pin definition file used in Hardware PLC - "pins.h". In this case sign "#" and the pin nam... sing direct hardware commands instead of Hardware PLC procedures allows to free up the Hardware PLC process and to prevent situations where long PLC command
- et15-rs485-modbus-rus
- s находится тут - {{http://docs.pv-automation.com/plc/plc_modbus_api}} В примере описывается подключение инвертора **Yaskawa v7**. === Проверить, что отс... the Modbus device is controlled directly from the PLC procedure, "RS485/Modbus communication" checkbox... Lathe > Spindle configuration dialog </code> {{:plc:modbus-plc-002-spindle.png}} === Для Hardware P
- dental_aligners
- igners in myCNC====== Relevant articles: * [[plc:plc|PLC]] * [[mycnc:mycnc_screen_configuration|Screen Editing and Configuration]] * [[mycnc:dental_mil... iables can be interacted with either via Software PLC (as in the example below, via HANDLER_INIT), or v
- tangential_knife_support
- png}} The #7005 variable can be set in Software PLC, "HANDLER_INIT.plc". Software PLC procedure HANDLER_INIT is running at the start of myCNC control software right after a... 5,1); </code> For example <code C __HANDLER_INIT.plc> main() { gvarset(60000,1); //run Servo ON p