Differences

This shows you the differences between two versions of the page.

--- sidebar [2020/07/23 08:39] – ivan
+++ sidebar [2023/06/05 15:58] – ivan
@@ Line 20: / Line 20: @@
     * [[mycnc:mycnc_et6|MyCNC-ET6 Controller]]
     * [[mycnc:mycnc_et7|MyCNC-ET7 Controller]]
-    * [[mycnc:mycnc_et10|MyCNC-ET10 Controller]]
+    * [[mycnc:mycnc_et9|MyCNC-ET7R4 (ET9) Controller]]
+    * [[mycnc:mycnc_et10|MyCNC-ET10 Controller (R3)]]
+    * [[mycnc:mycnc_et10_r2|MyCNC-ET10 Controller (R2)]]
     * [[mycnc:mycnc_et15|MyCNC-ET15 Controller]]
     * [[mycnc:wireless_pendants|Wireless Pendants]]
@@ Line 28: / Line 30: @@
     * [[mycnc:touchscreen_setup|Touchscreen setup and calibration]]
     * [[mycnc:mql|MQL - Minimum Quantity Lubrication]]
+    * [[mycnc:dc_motor_control|DC Motor Control]]
+    * [[mycnc:dental_aligners|Dental Aligners]]
   * **[[mycnc:mycnc_software|MyCNC Software]]**
     * [[mycnc:mycnc|Main Software Features]]
     * [[mycnc:mycnc_advantages|Main Advantages of myCNC software]]
-    * [[mycnc:mycnc_screen|Screen Description]]
+    * [[mycnc:mycnc_screen|Profile Screen Description]]
     * [[mycnc:mycnc_screen_configuration|Screen Editing and Configuration]]
     * [[mycnc:mycnc_setup|Software Setup]]
       * [[mycnc:MyCNC Configuration Dialogs]]
+      * [[mycnc:mycnc_configuration_dialogs_unfolded]]
     * [[mycnc:MyCNC Profiles]]
     * [[mycnc:MyCNC Setup Examples]]
@@ Line 63: / Line 68: @@
     * [[mycnc:subroutines|Subroutines]]
     * [[mycnc:popup_messages|Popup Messages]]
+    * [[mycnc:pipe_cutting|Pipe Cutting]]
+    * [[mycnc:laser_cutting|Laser Cutting]]
+    * [[mycnc:speed_priority|Speed Priority]]
+    * [[mycnc:drilling_cycle|Drilling Cycle]]
+    * [[mycnc:scriber|Scriber]]
+    * [[mycnc:hard_pendant|Hardware Pendant]]
+    * [[mycnc:dental_mill|Dental mill]]
   * [[mycnc:sbc|SBC - Single Board Computer]]
@@ Line 92: / Line 104: @@
   * [[mycnc:ihc|IHC]]
   * [[mycnc:independent_pulse_generator|Independent Pulse Generator]]
+  * [[mycnc:low_frequency_pulse_generator|Low Frequency Pulse Generator]]
+  * [[mycnc:hypertherm_agc|Hypertherm Automatic Gas Console]]
   * [[examples:plasma|MyCNC Plasma Configuration Example]]
   * [[mycnc:mycnc_setup_examples#how_to_set_up_two_instances_of_mycnc_software_on_one_machine|Setup of two myCNC instances on one machine]]
@@ Line 109: / Line 123: @@
     * [[other:language-localization|Language Localization]]
     * [[other:5v-converters|Line driver to 5V converters]]
+    * [[other:console_commands|Console commands]]
+    * [[other:sheetcam|SheetCam Tips]]
+    * [[other:manual_firmware_reflash|Manual Firmware Reflash]]