myCNC Online Documentation

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Speed Priority ======


This article is designed to introduce the reader to speed priorities in myCNC. All values are written in order of priority within its mode (from highest to lowest). The three main modes that you will encounter that change the speed priorities are the following:

  * **Cutting** 
    * The general cutting mode that you will most often work with 
  * **Simulation**
    * More info on the simulation mode is available [[examples:plasma-x1366p#simulation_mode|here]]
  * **Marking** 
    * Marking can be enabled within the general Cutting and Simulation modes. More information on marking is available [[examples:plasma-x1366p#scriber|here]].


----

===== Priorities in cutting mode =====

** 1.** **Arc cutting speed**, if arc radius is smaller than the one specified in settings and Arc Speed Control is enabled \\
 **2.** **Marking speed**, if the marking mode (M45-M46) is enabled \\

If the two speeds above are not applicable, check global variable **#7696 (GVAR_CUTCHART_FEEDRATE_PRIORITY)**. The toggle for this global variable is available in //Settings > Config > G-codes Settings > Ignore Feedrate (use Cutcharts for cutting speed).// \\ 

====Priorities if #7696 is equal to 0:====

 **3.** **F-code** for the speed, if an F-code is present in the program \\
 **4.** **Cutcharts speed (#7605)**, if not zero \\
 **5.** **Default feed rate**, if no F-codes or cutcharts speed \\

====Priorities if #7696 is equal to 1:==== 

 **3.** **Cutcharts speed (#7605)**, if not zero \\
 **4.** **F-code** for the speed, if an F-code is present in the program \\
 **5.** **Default feed rate**, if no F-codes or cutcharts speed \\


----

===== Priorities in simulation mode =====

 **1.** **Simulation speed**, if simulation mode speed (global variable **#7061**) is set to value is greater than 0 \\
 **2.** **Arc cutting speed**, if arc radius is smaller than the one specified in settings and Arc Speed Control is enabled \\

When the two speeds above are not applicable, check the mode (**marking** or **cutting**). \\

 **3.** If **marking mode** (M45-M46) is enabled, use **marking speed** \\
OR \\
 **3.** If **cutting mode** is enabled, then then use **rapid speed** if the flag in global variable **#7530** (GVAR_DRAWING_FAST, rapid speed simulation) is not set to 0 

In cases where you are in **cutting mode** and there is **no flag in #7530** (#7530==0), check global variable **#7696** (GVAR_CUTCHART_FEEDRATE_PRIORITY). The toggle for this global variable is available in //Settings > Config > G-codes Settings > Ignore Feedrate (use Cutcharts for cutting speed)//. \\ 

====Priorities if #7696 is equal to 0:====

 **3.** **F-code** for the speed, if an F-code is present in the program \\
 **4.** **Cutcharts speed (#7605)**, if not zero \\
 **5.** **Default feed rate**, if no F-codes or cutcharts speed \\

====Priorities if #7696 is equal to 1:==== 

 **3.** **Cutcharts speed (#7605)**, if not zero \\
 **4.** **F-code** for the speed, if an F-code is present in the program \\
 **5.** **Default feed rate**, if no F-codes or cutcharts speed \\

=====Flow chart=====

The following flow chart describes the information listed above in a visual manner: 

{{:mycnc:speed-priority-003-flowchart.jpg}}

For more information on the global variables listed in this article, please consult the [[mycnc:global_variables|Global Variables List]].