mycnc:mycnc_configuration_dialogs
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
mycnc:mycnc_configuration_dialogs [2019/06/04 11:59] – ivan | mycnc:mycnc_configuration_dialogs [2019/06/24 12:48] – ivan | ||
---|---|---|---|
Line 104: | Line 104: | ||
==== Axes/Motors ==== | ==== Axes/Motors ==== | ||
+ | |||
{{mycnc: | {{mycnc: | ||
- | The main axes-motors parameters can be configured in the dialog | + | The main axes-motors parameters can be configured in the settings by going to **CNC Settings > Axes/ |
- | 1. **Enabled.** Each of axes X, | + | 1. **Enabled.** Each of the motors for axes X, |
- | 2. **Pulses per unit**. This parameter | + | 2. **Pulses per unit**. This parameter |
- | 3. **MaxSpeed** - CNC control will limit machine speed for each axis with this value. Note that **MaxSpeed** | + | 3. **Max Speed** - CNC control will limit machine speed for each axis by this value. Note that the Max Speed does not count the override % value. Be careful |
- | 4. **Backlash** - Backlash value in units (mm/inch) for each axis | + | 4. **Backlash** - Backlash value in units (mm/inch) for each axis (different for each machine depending on the hardware specifications) |
5. **Axes Mapping** - Toolpath planner uses this setting for tool motion speed calculation. Possible settings are- | 5. **Axes Mapping** - Toolpath planner uses this setting for tool motion speed calculation. Possible settings are- | ||
* " | * " | ||
- | * " | + | * " |
- | * " | + | * " |
- | * " | + | * " |
- | * " | + | * " |
6. **Speed profile** - additional settings to optimize Speed profile for rotary axes | 6. **Speed profile** - additional settings to optimize Speed profile for rotary axes | ||
- | * " | + | * " |
- | * "Slave Of XYZ" - Current speed calculated for X,Y,Z axes depends | + | * "Slave Of XYZ" - Current speed calculated for X,Y,Z axes depending |
* " | * " | ||
- | 7. < | + | 8. **Attach to axis**. Any of 6/8 motor output can be attached to any axis. Here you can select what axis is used for every motor output. |
- | + | ||
- | 8. **Attach to axis**. Any of 6/8 motor output can be attached to any axis. Here you can select what axis is used for every motor outputs. | + | |
- | 9. **Inversion** - Put checkbox if need to change rotation direction for any axis. | + | 9. **Inversion** - Mark the checkbox if you need to change |
< | < | ||
- | For example, | + | For example, |
Invertion is selected for Output #1, so both motors connected to Output#0 and Output# | Invertion is selected for Output #1, so both motors connected to Output#0 and Output# | ||
- | will be rotated simultaneously, | + | will be rotated simultaneously, |
Line 372: | Line 371: | ||
==== Network | ==== Network | ||
{{mycnc: | {{mycnc: | ||
+ | |||
+ | ====Motion==== | ||
+ | |||
+ | Upon opening the Motion tab in Settings, you are presented with the following window: | ||
+ | |||
+ | {{: | ||
+ | |||
+ | The following settings can be edited in the Motion tab: | ||
+ | |||
+ | **CV Tolerance** signifies the amount of " | ||
+ | |||
+ | **S-curve smooth filtering** specifies the time the controller gives the machine to adjust its acceleration during sharp turns. A larger value allows for a larger impulse time, resulting in less stress to the hardware. 41ms is recommended. | ||
+ | |||
+ | **Look Ahead Break Angle**. If the angle is larger than this, the machine will stop at corner completely in order to allow for a sharper cut. | ||
+ | |||
+ | **2D Cutting** is used on plasma/gas machines which lack a configurable z-axis. | ||
+ | |||
+ | **Step-jog count** specifies whether the user wants the machine to monitor the inputs sent to it as it is already moving or not. If selected, the machine will count however many signals are sent to it even if it is moving already, if not selected then the machine will ignore other signals until it has completed its initial movement. | ||
+ | |||
+ | **Sync G0 & (G1, G2, G3) Overspeed** allows the user to sync the rapid and cutting speeds, allowing the user to use one set of buttons to change them at the same time. | ||
+ | |||
+ | {{: | ||
+ | |||
+ | **Creep Speed** specifies the speed of the machine after it begins to cut into the working material. It is advisable to set it to be lower than the actual working speed for a small portion of time at the start of the cut. This time is specified in seconds. | ||
+ | |||
+ | **Overspeed**. The Jog, G0 and G1, G2, G3 Overspeeds signify the value by which the speed is higher/ | ||
+ | |||
+ | **Speed/ | ||
==== Camera | ==== Camera | ||
- | {{mycnc:configuration:mycnc-configuration--46.png}} | + | |
+ | {{:quickstart:mycnc-quick-start: | ||
+ | |||
+ | For a full overview of camera features and its setup process, please consult the [[quickstart: | ||
==== 5 axes RTCP ==== | ==== 5 axes RTCP ==== |
mycnc/mycnc_configuration_dialogs.txt · Last modified: 2022/10/28 15:51 by ivan