Differences

This shows you the differences between two versions of the page.

--- mycnc:mycnc_et7 [2019/06/27 13:43] – ivan
+++ mycnc:mycnc_et7 [2024/02/28 15:29] (current) – ivan
@@ Line 1: / Line 1: @@
 ===== myCNC-ET7 CNC controller =====
+//**NOTE**: The myCNC-ET9 controller (also labeled ET7R4, ET7R5 and ET7R6) is the updated version of the myCNC-ET7 board with some additional functionality. For information specific to the ET9 revisions, please consult the following manual: [[mycnc:mycnc_et9|myCNC-ET9 (ET7 R4)]]//
+^^myCNC-ET7 controller specifications^^
+| Number of motor outputs | 6 |
+| Motor driver outputs | pulse-dir, differential high-speed line driver outputs compatible with RS422 (TIA/EIA-422) standard |
+| Maximum pulse frequency | 3 MHz |
+| Binary inputs | 16x galvanic isolation, PNP/NPN sensor compatible |
+| Encoder inputs | 3x incremental encoder inputs,differential line driver (EIA RS422 compatible), hardware decoded, 5MHz max frequency |
+| Binary outputs | 5x - pluggable relays 10A, NO/NC contacts; 11x - open collector, 24V, 0.25A |
+| PWM outputs | 3x - open collector, 24V, 0.25A |
+| ADC inputs | 2x - 0...10V range, differential inputs, fully galvanic isolated (for plasma arc voltage measure, THC control), 6x - 0...3V range |
+| DAC output | 1x - 0...10V (for spindle speed control and relative applications)|
+| RS485/RS422 | 1x RS422 full duplex serial communication OR 2x RS485 half-duplex serial communication |
+| External operator panel connector | up to 25 external keys,  up to 2 rotary encodersup to 2 double-axes joysticks OR up to 4 potentiometers (shared with 4x ADC inputs) |
+| Power supply outputs for control computer | 2x DC-DC converters 5V 1.5A |
 ==== ET7 top view ====
@@ Line 6: / Line 22: @@
 ==== Power supply connection ====
-myCNC-ET7 control board uses 24VDC .
+myCNC-ET7 control board uses 24VDC.
-The board contains 4 pins for connection +24V (joined internally) and a number of GND pins for convenient connection of external devices.
+The board contains 4 pins for connection +24V (joined internally) and a number of GND pins for convenient connection of external devices. In the diagram below, the top-right 6 pin connector (with 3 pins for GND and 24V each) is used for easy connection of external devices.
-Power Supply 24V DC and +24V and GND pins are shown on a picture below.
+{{:mycnc:et7-power-connection-004.jpg}}
+A separate 4-pin connector is also available on the board (shown below). This one houses two independent power converters (5V/5V for all new ET7 boards, and 5V/12V for certain older ET7 models) with two GND pins:
+{{:mycnc:et7-power-connection-005.jpg}}
+For example, this 4-pin power supply connection is often used to power single board computers:
-{{hardware:et7:et7-power-connection-001.jpg}}
+{{:hardware:0pc-et7r2-004.jpg}}
@@ Line 96: / Line 119: @@
 {{hardware:et7:et7-encoder-inputs.png}}
-Encoder inputs connector pinout is shown on a picture
+Encoder inputs connector pinout is shown in the diagram below:
-{{hardware:et7:et7-encoder-inputs-connection-001.jpg}}
+{{:mycnc:et7-encoder-inputs-connection-003.jpg}}
+//NOTE: Depending on the board revision version, the +5/+5V power supply in the top left corner may actually be
+a +5/+12V power supply (on older boards).//
@@ Line 105: / Line 131: @@
 myCNC-ET7 controller has 8 ADC inputs.
   * 6 ADC inputs 0-5V range
-  * 2 ADC inputs with galvanic isolation for save and convenient connection of Arc Voltage signal from Power station. Galvanic isolated ADC inputs are 0..10V, so High Voltage Arc signal **CANNOT** be connected directly to ADC inputs, **voltage divider is NEEDED**.
+  * 2 ADC inputs with galvanic isolation for save and convenient connection of Arc Voltage signal from Power station. Galvanic isolated ADC input ADC0 has the 0...5V (low-voltage) range, while ADC1 is 0..12V, so High Voltage Arc signal **CANNOT** be connected directly to ADC inputs, **voltage divider is NEEDED**. **Please consult the information below for more info on the ADC0/ADC1 inputs.**
 The 0-5 V ADC inputs schematic is shown below:
@@ Line 118: / Line 144: @@
 {{:hardware:et7:et7-b-adc-connection-001.jpg}}
-Non-isolated ADC inputs have a 0...5V Range. Connector with non-isolated ADC inputs also has the GND and +5V DC output pins for convenient potentiometer connection. Picture below shows an  example for potentiometer connected to ADC2 input.
+Non-isolated ADC inputs (ADC0, ADC2-ADC7) have a 0...5V Range. Connector with non-isolated ADC inputs also has the GND and +5V DC output pins for convenient potentiometer connection. Picture below shows an  example for potentiometer connected to ADC2 input.
 {{:hardware:et7:et7-b-adc-connection-002.jpg}}
 <code>WARNING: The names for the ADC inputs printed at the bottom of the board are NOT correct.
+The silk printing naming for inputs ADC0 and ADC01 are switched.
 Please consult the above schematics for the ADC0/ADC1 input locations.</code>
+A voltage divider can be used for plasma cutting arc. For the 12V ADC ports (ADC1) and voltage in the range of 0-300V, a voltage divider with a 1:25 ratio may be used (a 1:20 ratio can be used for voltages up to 240V).
+For example, using the standard //Vout=Vin*(R2/[R1+R2])// formula, we can see that for a 1:20 ratio, the resistors must be selected in such a way as to achieve a R1=19*R2 ratio.
+{{:mycnc:et7-b-adc-connection-004-voltage-divider-adc1.jpg}}
+Similarly, for ADC0 (with a range of 0-5V), a voltage divider with a 1:50 ratio is required (for voltages up to 300V). On older (prior to 2020) models of the myCNC-ET7 controller, the range on the ADC0 inputs was similarly 0-12V, however in the interest of user convenience the two ADC ports can now be used for a variety of power sources and voltage dividers.
+{{:mycnc:et7-b-adc-connection-005-voltage-divider-adc0.jpg}}
 ==== Jumpers J1, J2, J3 and J4 ====
@@ Line 148: / Line 185: @@
 {{hardware:et7:et7-rs485.png}}
-RS422 connector pinout shown below
+RS422 connector pinout shown below. **NOTE**: While all of the RX/TX ports (RX A, RX B, TX A, TX B) are used for the RS422 connection (such as a Hypertherm machine), only RX A and RX B are utilized in an RS485 configuration.
-{{:hardware:et7:et7-b-rs422-connection-001.jpg}}
+{{:mycnc:et7-b-rs422-connection-002-rs485-connections.jpg}}
 ==== DAC output ====
@@ Line 161: / Line 200: @@
 ==== Connection Examples ====
+===Stepper driver connection (4 axes)===
+{{:mycnc:et7-stepper-driver-003.jpg}}
 === 3-wire NPN sensor connection example (external power supply)===
@@ Line 278: / Line 322: @@
 ==== ET7 firmware reflash ====
+//**WARNING:** Unlike updating the myCNC software, the firmware CANNOT be downgraded after a reflash. The myCNC team recommends reflashing the control board firmware as a last resort only, and recommends seeking an explicit confirmation from the support team that the firmware reflash is warranted in order to avoid issues.//
+:!: //**NOTE:** Make sure to select the firmware for the correct version/revision of your board! Firmware for ET7 boards (R1-R3) and ET7 boards (R4-R6, also known as the ET9) are __DIFFERENT.__
+Flashing incorrect version of the firmware will result in a non-functional board. If you're unsure of your board version, please contact myCNC Technical Support prior to the reflash://
+{{:mycnc:et7-reflash-different-versions.png}}
+----
 myCNC-ET7 reflashing procedure may take up to 3 minutes.
@@ Line 295: / Line 349: @@
 . Open myCNC software on Host computer (Settings > Support Tab)
-. "Select board" set to "myCNC-ET7"
+. "Select board" set to "myCNC-ET7". Make sure to select the correct revision version (R1/R2/R3 or R4/R5/R6).
 . Select "Firmware version" from "Release", "Night build" or "Testing" ("Release" is recommended)
@@ Line 307: / Line 361: @@
 . If "Sector 0; +" message is shown in the debug window, the reflashing process has been finished successfully.
-. Remove all jumpers (J4, J5) and restart the board.
+. Remove all jumpers (J5, J6) and restart the board.
 {{:mycnc:et7-reflash-002-support.png}}
-If the reflashing process failed, please repeat the procedure from Step 3.
+{{:mycnc:et7-reflash-004-success.png}}
+If the reflashing process failed, please check your internet connection and the micro-USB connection, and then repeat the reflashing procedure from Step 3.
+======myCNC-ET9 (ET7-R4 and above)======
+The myCNC-ET7R4 (also called the myCNC-ET9) controller is the updated version of the myCNC-ET7 board with some additional functionality. For information on the ET7, please consult the following manual: [[mycnc:mycnc_et7|myCNC-ET7 CNC controller]]
+The board naming is different due to a different chip, which requires a separate version of the firmware from the regular ET7 boards (such as ET7R3).
+//NOTE: The ET7R5 (Revision 5) and the ET7R6 (Revision 6) controllers use the same ET9 firmware as ET7R4. The functionality between R4 and R5/R6 versions of the board remains the same. //
+----
+The ET7R4 controller is pictured below:
+{{:mycnc:et9-001.jpg}}
+The myCNC-ET9 pictured with a DC motor driver:
+{{:mycnc:et9-002-dc.jpg}}
+myCNC-ET9 main features in addition to the fucnctionality present on the previous iterations of the board:
+  * Motor driver can be plugged into an auxiliary connector (outputs #17/#18)
+  * 2 PWM ports duplicated (PWM1, PWM2)
+  * Since the driver board is designed for 2 motors, therefore the ET9 has support for both
+==== Reflashing the ET9 board ====
+Reflashing the ET9 board
+To reflash the ET9 board, follow the instructions on reflashing the ET7 boards here, however make sure to select the **ET7-R4/R5/R6 (ET9)** option in the Select Board field.
+{{:mycnc:et7-reflash-different-versions.png}}
+Failure to select the correct revision version of the board will result in your board being non-operational. Please consult the myCNC support team prior to a reflash should you have any questions.