Differences

This shows you the differences between two versions of the page.

--- mycnc:mycnc_setup_examples:plasma_cutting:1366p [2019/06/21 12:37] – ivan
+++ mycnc:mycnc_setup_examples:plasma_cutting:1366p [2019/10/10 11:15] – ivan
@@ Line 58: / Line 58: @@
 |{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-052-laser-pointer.jpg}}| Switch the instrument to laser pointer |
-====Part selection and editing====
+====G-code tab (Part selection and editing)====
-|{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-046-previous-part.jpg}}| Go to previous part |
+|{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-046-previous-part.jpg}}| Go to previous part. The plasma cutting files often consist of a large number of small parts that will be cut out from the working material. This button allows to navigate between the different parts of the G-code file to quickly move back if necessary. |
 |{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-045-next-part.jpg}}| Go to next part |
 |{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-047-specific-part.jpg}}| Go to a specific part number |
-|{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-048-cloning.jpg}}| Open part cloning window |
+|{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-048-cloning.jpg}}| Open part cloning window. This allows to quickly multiply the existing G-code file and to arrange it on the working material in the operator's preferred way.  |
-|{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-049-ab-cut.jpg}}| Cut from point A to point B |
+|{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-049-ab-cut.jpg}}| Cut from point A to point B. This allows to do a manual straight line cut between two points. Upon clicking the A-B Cut button in the G-code tab, a small window appears which allows the user to set some point, then move the machine away and then click A-B Cut to begin the cutting process.  |
-|{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-050-rotate.jpg}}| Open part rotation window |
+|{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-050-rotate.jpg}}| Open part rotation window. This window will allow the user to rotate the program file by a set angle or mirror the program file about some axis. |
+====Plasma tab (LED indicators and drill operation)====
+The G-code profile is presented below:
+{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-053-plasma-tab.png}}
+This screen presents the user with the options and indicators for the plasma controls. The five buttons on the right side of the tab are the most commonly used:
+| {{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-057-surface-measure.jpg}}  |   |
+| {{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-058-plasma-on.jpg}} |  |
+| {{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-059-xyz-homing.jpg}}  |  |
+| {{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-060-servo-on.jpg}} |  |
+| {{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-061-servo-off.jpg}} |  |
+The LED panel on the left of the G-code tab shows the current state of the main plasma components (whether the plasma machine has power, if the arc sensor is on, the IHC indicator for the initial contact with the metal, THC and THC Low Speed LEDs which indicate whether the Torch Height Control is ON or OFF, and the Scriber LED which shows if the marking process is on or off (marking can be done with a smaller plasma torch or with an etching working tool):
+{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-054-leds.png}}
+The Drill window allows the user to control the drill attached to some motor on the machine to be used for hole cutting, which is typically operated through the use of some pneumatic or spring mechanism to push the drill module down to the metal. The most common drill modules that myCNC is used on utilize two valves to move the drill up/down, as well as two sensors to register when the drill is in the up/down position. Therefore there are two LEDs for both the valves and the sensors, as well as an indicator LED for whether the drill module is or or not.
+The M08 button begins the M08 PLC procedure, which involves turning the drill on and operating the valves to press the module into place. The up/down buttons allow the user to move the entire module in the z-axis via the motor that is connected to operate the drill module (note that this is separate from the valves which operate only when smaller distances are involved). The drill depth from the top of the working material can also be set in mm:
+{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-055-drill.png}}
+The homing sensors LED show two sensors per the X, Y and Z axes. Not all of these sensors are commonly used during the homing procedure on different machine setups, so the user is free to edit the ''x-plasma.xml'' file in the X1366P profile folder to not display the unnecessary LEDs:
+{{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-056-homing-sensors.png}}
 ====Custom Machine Settings (User Settings)====
@@ Line 75: / Line 103: @@
 ====Progress bar====
-The progress bar for the control program is present in the latest versions of myCNC plasma cutting software.
+The progress bar for the control program is present in all the recent versions (X1366 series) of myCNC plasma cutting software.
 {{:mycnc:mycnc_setup_examples:plasma_cutting:screen-1366p-051-progress-bar.jpg}}